TX-100

可調式雷射氣體分析儀

TX-100 是 HORIBA 的雷射 HCl 分析儀，配備探針式光學系統。 TX-100 適用於監測焚化廠煙氣流中的 HCl 濃度以及控制 HCl 去除過程。

事業部: Process And Environmental

產品分類: Combustion

製造商: HORIBA, Ltd.

探針式光學系統雷射和接收器安裝在堆疊的同一側

只需安裝一個Flange即可完成設置
輕鬆更換現有分析儀，無需額外工作
穩定的光軸提供卓越的性能
連續水分校正功能支援高精度測量

HORIBA獨創的校準機制

TX-100 可以在不中斷設施運作的情況下實施校準。自動校零，訊號長期維持穩定

（美國專利號：8934101；中國專利號：ZL201280039440.7；已申請日本、歐洲專利）

<測量> 零點檢查和測量交替進行調零方式將棱鏡以固定間隔插入光路時進行零點檢查。

測量模式

測量模式下，棱鏡向上移動並離開光路

<校準>

在校準池中進行校準氣體校準完成後，探頭仍連接在煙囪中。

TX-100的資料管理可以從各種元件中進行選擇；分析儀的顯示器、HMI（人機介面）單元或來自 PC-HMI 軟體

分析單位顯示

顯示確認及控制設備狀態、瓦斯狀態、通訊狀態等資訊。

HMI 單元（可選）

觸控螢幕可設定並確認濃度、透過率、趨勢圖、維護資訊、警報狀態等。

PC-HMI（軟體）

PC-HMI是一個軟體，其功能與HMI單元中安裝的軟體幾乎相同。將本軟體安裝在PC或其他裝置上即可進行操作。 PC 與 TX-100 之間可透過乙太網路進行資料傳輸。可從我們的網站免費下載。

相關產業

Waste to Energy Power Generation

Name	Tunable Laser Gas Analyzer
Model	TX-100
Measurement target	HCl and H₂O in process gas
Measurement component	HCl, or HCl and H₂O simultaneous measurement
Measurement principle	Non Dispersive Infrared (NDIR)
Measurement type	Probe type
Laser class	CLASS1(IEC60825-1: 2014)
Protection degree	IP65
Wetted materials	SUS316L、SUS304、BK7、FKM、PTFE、aluminum alloy
Tube connections	Rc1/8 (Tube of 8 mm O.D./6 mm I.D.)
External dimentions	Analyzer: Max: 358 (W) x 517 (D) x 453 (H) mm Probe Flange diameter (Max.): Φ235 mm、 Length: 1500 mm Probe diameter: Φ 89 mm
Weight	Analyzer: 19 kg Probe: 20 kg
Flange specifications	JIS10K-100AFF、JIS5K-125AFF、ANSI 150 Lb 4BRF
Power supply voltage	DC24V±10%
Power consumption	90 W
Display	LCD (128 × 64 dots), LED (3 units: Status display)
Display contents	Gas concentration, transmission, process gas temperature, process gas pressure, system status, alarm information, system information (product serial no., output signal, IP address, optical path length, analyzer unit internal temperature)
Communication	Modbus^TM/TCP
Analog input/output	Input: Two channels (Process gas temperature, process gas pressure) 4 to 20 mA (isolated input)
Analog input/output	Output: Two channels (Process gas concentration*, transmission, process gas temperature, process gas pressure) 4 to 20 mA (isolated output) Max. load: 550 Ω
Digital input/output	Input: One channel (External alarm) Non-voltage digital input (isolated input) Input open signal: 100 kΩ or more Input close signal: 200 Ω or less
Digital input/output	Output: Two channels (Warning/Calibration/Warm-up/Maintenance state/Fault) Relay contact output (isolated output) Max. 24 V, 1 A at each terminal

*You can select either fixed value or real time HCl correction using H₂O concentration.
-Modbus is a trademark of Schneider Electric Inc.
-Consult HORIBA if special probe length is required.

Performance

Measurement component	HCl, H₂O
Measurement range (250℃、101.3kPa)	HCl: 0-50,100,200,300,400,500 ppm^1 H₂O:* 0-50 vol%
Measured optical path length	2m
Repeatability	HCl: /- 1.0% F.S. H₂O: /- 2.0% F.S.
Linearity	HCl: /- 1.0% F.S. H₂O: /- 2.0% F.S.
Zero drift	/- 2.0% F.S. / 6 months
Span drift	/- 2.0% F.S. / 6 months
Data update cycle	Approx. 2sec
Recommended Calibration cycle	6 months
Calibration method	HCl: Manual calibration using gas cell H₂O: Factory calibration^*2
Interference	/- 2.0% F.S. Gas conditions (at standard process gas condition range)
Warm-up time	3hours

*1: Select a measurement range.
*2: You can adjust the H₂O indicated value to the manual analysis value. Consult HORIBA for more details.

Usage Conditions

Ambient temperature	-20 ～ 55°C (no direct sun rays, radiant heat and heat conduction from flange)
Ambient humidity	Relative humidity: 90% or less (no condensation)
Dust	Ambient criterion or less
Air purge	Instrument air (must not contain oil or mist; no dew formation) Pressure: 0.2 to 0.25 MPa*
Air purge flow rate	60 L/min or more (depend on the process gas conditions)
Vibration	At 1 to 200 Hz, 1.96 m/s2 or less (excluding resonant frequency)
Process gas conditions	Temperature: 150 to 250°C Pressure: 101.3 ± 10 kPa Flow speed: 25m/s Dust: 0.1mg/Nm³ or less

* This value is supplied pressure to TX-100 main unit. In case air passes through the purge unit, the pressure value at the purge unit is 0.2 to 0.9 MPa.