HP-200 Field-installation type pH meter

Lineup of a wide range of electrodes
A wide variety of electrodes are offered to cater to different needs.

Comprehensive range of cleaning devices.
A diverse lineup of cleaning devices are offered. Particularly, ultrasonic cleaners are advantageous as they do not require water or air, making them convenient for retrofitting existing HP-200 installations on site. The drop-in type of cleaning device, which fits into a holder, offers ease of maintenance.

Product name			pH meter
Model			HP-200
Combined sensor			Glass electrode
Measurable range	pH		pH0 to pH14 (display range: pH−1 to pH15)
Measurable range	Temperature		0℃ to 100℃ Display range : −10℃ to 110℃(the sensor types are detected automatically) Display range : −20℃ to 130℃(the sensor types are input by manually)
Display resolution capability	pH		0.01 pH
Display resolution capability	Temperature		0.1℃
Efficiency	pH	Repeatability	Within ±0.03 pH (response for equivalent input)
	pH	Linearity	Within ±0.03 pH (response for equivalent input)
	Temperature	Repeatability	±0.3℃ (response for equivalent input)
	Temperature	Linearity	±0.3℃ (response for equivalent input)
Transmission output	Number of outputs		2 (the negative terminals for transmission outputs are internally connected and at the same electric potential)
	Output type		4 mA to 20 mA DC: input/output isolated type
	Load resistance		Max: 900Ω
	Linearity		Within ±0.08 mA (output only)
	Repeatability		Within ±0.02 mA (output only)
	Output range	Output 1	pH: Selection from preset ranges or free range input within measuring range.
	Output range	Output 2	Temperature: Free setting within a range between −20℃ and 130℃
	Occasional out for error		Hold or burnout to either 3.8 mA or 21 mA
	Transmission hold		In the maintenance mode, transmission signal is held at the latest value or preset value. In the calibration mode, transmission signal can be alive or held.
Contact output	Number of output		5
	Output type		No-voltage contact output
	Contact type		Relay contact; SPDT (1c)
	Contact capacity		250 V AC, 3 A; 30 V DC, 3 A (resistance load)
	Contact function	R1, R2	Selectable from upper limit alarm, lower limit alarm, ON/OFF control, and time-sharing proportional control.
		R3, R4	Selectable from upper limit alarm, lower limit alarm, ON/OFF control, currently holding of transmission output, and cleaning output.
		FAIL	Error alarm
	Alarm setting range		Setting range: 0.00 pH to 14.00 pH Delay time: 0 seconds to 600 seconds
	Control function	ON/OFF	Setting range: 0.00 pH to 14.00 pH Control width: 0.02 pH to 4.00 pH (−0.01 pH to 2.00 pH)
	Control function	Time-sharing proportional control	Setting range: 0.00 pH to 14.00 pH Proportional band: 0.02 pH to 4.00 pH Period: 5 seconds to 300 seconds Control duty ratio shift function: 50% to 100% at the alarm setting point. Variable off time extension in the F-zone: When the deviation enters a certain range (Fine-zone), the off time of the duty is automatically extended accordingly. This function is disabled when the duty ratio shift function is enabled. F-zone: 1% to 100% of proportional band (when the deviation enters the above range, the automatic off time extension is enabled.) Max. off time extension: 0 second to 300 seconds Max. duty setting: 50% to 100% (regardless of the proportional band)
Cleaning output	Number of outputs		1
	Output type		AC power control output (applied power supply voltage)
	Contact type		Relay contact, SPST (1a)
	Contact capacity		250 V AC 0.5 A
	Contact function		Solenoid valve for cleaning control
	Settings	Cleaning period	0.1 hours to 168.0 hours
		Cleaning time	2 seconds to 600 seconds
		Hold time	2 seconds to 600 seconds
	Timer accuracy		Within 2 minutes per month
	Description of cleaning operation		One of the following operations. Operation of internal timer only Operation of internal timer and external input command Enable the internal timer only when external input is active. The cleaning trigger signal (the external trigger signal must be longer than 2 seconds).
Contact input	Number of inputs		1
	Contact type		No-voltage "a" contact for open collector
	Conditions		ON resistance: 100 Ω max. Open voltage: 24 V DC Short-circuit voltage: 12 mA DC max.
	Contact function		External input for cleaning or transmission holding if cleaner is not attached.
Communication capability	Communication method		RS-485
Communication capability	Signal type		2 wire system, isolated from the input circuit Not isolated from transmission circuit
Temperature compensation	Applicable temperature element		Platinum resistor: 1 kΩ (0℃)
	Applicable temperature element		Normal characteristic temperature-sensitive resistor: 500 kΩ (25℃), 6.8 kΩ (25℃),10 kΩ (25℃)
	Element selection method		Automatic temperature sensor type detection or manual selection (no temperature element is selectable)
	Temperature compensation range		0℃ to 100℃
	Temperature calibration		1 point calibration comparing reference thermometer
Calibration	Calibration method		Auto or basic (manual) calibration
	Number of calibration points		Selectable from 1, 2, and 3 points
	Kinds of standard solutions		pH 2, 4, 7, 9, and 10
	Kinds of standard solutions		Any pH standard solution (with difference of 2 pH or more) for basic calibration
	Additional capabilities		Automatic detection of kind of standard solution
			Automatic detection of electric potential stability
			Automatic detection of calibration failure (asymmetry potential, sensitivity, or response time)
			Calibration history (asymmetry potential, sensitivity, and number of days elapsed after last calibration)
Self-check	Calibration error		Asymmetry potential error, sensitivity error, and response time error
			Temperature calibration error
			Standard solution detection error
	Electrode diagnostic error		Cracking of glass response membrane
			Reference electrode impedance error (only applicable for differential circuit mode with a liquid ground electrode)
			Temperature sensor short-circuit, temperature sensor disconnection, and deviation from temperature measurement range
	Meter error		CPU error, ADC error, and memory error
Operating temperature range			−20℃ to 55℃ (without freeze)
Operating humidity range			Relative humidity: 5% to 90% (without condensation)
Storage temperature			−25℃ to 65℃
Power supply	Rated power supply voltage		100 V to 240 V AC ±10% 50/60 Hz
	Power consumption		15 VA (max)
	Others		With power switch for maintenance use
Compatible standards	CE marking		EMC :EN61326-1 Class A, Industrial electromagnetic environment Safety :EN61010-1 RoHS　 :EN50581 9. Industrial monitoring and control instruments
Compatible standards	FCC rules		Part15 Class A
Structure	Installation		Outdoor installation type
	Installation method		Mount on 50 A pole or wall
	Protection code		IP65	IEC60529, JIS C0920
	Case material		Aluminum alloy (coated with epoxy-denatured melamine resin)
	Material of fittings		SUS304
	Material of hood		SUS304 stainless steel (coated with epoxy-denatured melamine resin)
	Material of window		Polycarbonate
	Display element		Reflective monochrome LCD
External dimensions			180 (W) mm × 155 (H) mm × 115 (D) mm (excluding the fittings)
Mass			Main body: Approx. 3.5 kg Cover and fittings: Approx. 1 kg

*1 :The standard for effect on the reading by the electromagnetic field of the radiated radio frequency and by the conducted interference is within the measured pH value ±0.25pH.
*2 : When the sensor cable, the transmission cable, or the contact input cable is extended by 30 m or more, the surge test under the EMC Directive for CE marking is not applied.

Note

An arrester (spark over voltage: 400 V) is implemented for transmission output, contact input, and communication. However, use a most suitable surge absorption element on the connection lines in accordance with the ambient environment, the situation of equipment installed, and the externally connected equipment.

Size: 5.24 MB

〈Catalog〉Industrial Water Quality Measuring Instruments

HP-200

Field-installation type pH meter

HORIBA's long-selling water quality meter that excels in both indoor and outdoor applications.

Lineup of a wide range of electrodes

Comprehensive range of cleaning devices.

Note

Request for Information