perfevent.conf(5) — Linux manual page

NAME | SYNOPSIS | DESCRIPTION | FILE FORMAT | SEE ALSO | COLOPHON

PERFEVENT.CONF(5)          File Formats Manual         PERFEVENT.CONF(5)

NAME         top

       perfevent.conf - the Performance Co-Pilot perfevent PMDA
       configuration file

SYNOPSIS         top

       $PCP_PMDAS_DIR/perfevent/perfevent.conf

DESCRIPTION         top

       The perfevent.conf configuration file defines which hardware
       performance counters are enabled by the perfevent PMDA.

       The configuration file contains a list of events that should be
       enabled for each PMU. The perfevent PMDA detects which PMUs
       present and programs the configured events. If multiple PMUs are
       available, the perfevent PMDA uses the order of the entries in
       the configuration file to determine which PMU settings to use.
       The entries at the top of the configuration file have higher
       precedence.  Only one PMU configuration setting is used. The
       configuration file may also contain perf derived events. A
       derived event has a list of events which must be listed as base
       events. The values for the counters in the derived events are
       aggregated and displayed.

FILE FORMAT         top

       The file consists of one or more groups of PMUs and the events
       that go with them.

       The PMU identification string is enclosed in brackets and one or
       more events are listed below, one per line.

              ["PMU identification string"]
              EVENT_NAME [CPU OPTION]
              ...

       For derived events, one or more groups of events can be specified
       where, counters in one group can be specific to one architecture
       and the counters in other group can be specific to some other
       architecture. Else, only one group can be specified.
       EVENT_NAME_1, EVENT_NAME_2 etc. belong to group 1 and
       EVENT_NAME_3, EVENT_NAME_4 belong to group 2 and so on. If any of
       the event in the first group is not available, entire group will
       be discarded. And, the next group will be checked. The first
       group with all the events available will be activated and
       monitored. The derived perf event is enclosed in brackets along
       with :derived as a suffix. Note that the EVENT_NAME listed under
       derived event must be present as a base event in the
       configuration file. And, all the events under a particular
       derived perf event group must have the same CPU_OPTION. || acts
       as a separator for different groups inside a single derived
       event. The syntax is :

              [event:derived]
              EVENT_NAME_1 [CPU_OPTION] [scale]
              EVENT_NAME_2 [CPU_OPTION] [scale]
              ...
              ||
              EVENT_NAME_3 [CPU_OPTION] [scale]
              EVENT_NAME_4 [CPU_OPTION] [scale]
              ...

              The available event cpu options are as follows:

              cpu    to add the counter to all cpus in the system

              cpu_rr to add to one of the cpus in a round-robin
                     allocation strategy

              node   to add the counter to the first cpu in each numa
                     node

              node_rr
                     to add the counter to the cpus in each numa node in
                     a round-robin allocation strategy

              [N]    where N is the numerical digit of the CPU index

              if the CPU option is absent then the event is programmed
              on all cpus.

              scale is applicable for the counters in derived events. If
              scale is given, the counters will be scaled to their
              respective values. The options are as follows :

              a float value
                     Can be a simple float value, or a value in
                     scientific notation.

              perf_scale
                     The scale will be taken from the kernel sysfs scale
                     file entry for that event. Its generally specified
                     in
                     /sys/bus/event_source/device/events/<event_name>.scale

              If no scale is given, the default scale will be taken as
              1.0.

              Blank lines are ignored. Lines that begin with the # sign
              are ignored.

              Multiple, comma separated, PMUs may be specified in the
              PMU definition.

SEE ALSO         top

       pmdaperfevent(1).

COLOPHON         top

       This page is part of the PCP (Performance Co-Pilot) project.
       Information about the project can be found at 
       ⟨http://www.pcp.io/⟩.  If you have a bug report for this manual
       page, send it to [email protected].  This page was obtained from the
       project's upstream Git repository
       ⟨https://github.com/performancecopilot/pcp.git⟩ on 2024-06-14.
       (At that time, the date of the most recent commit that was found
       in the repository was 2024-06-14.)  If you discover any rendering
       problems in this HTML version of the page, or you believe there
       is a better or more up-to-date source for the page, or you have
       corrections or improvements to the information in this COLOPHON
       (which is not part of the original manual page), send a mail to
       [email protected]

Performance Co-Pilot               PCP                 PERFEVENT.CONF(5)

Pages that refer to this page: pmdaperfevent(1)