Single channel LoRa UDP packet forwarder ideal for development or testing purposes. Receives and transmits bidirectionally. This project is ideal for DIY of one of the cheapest LoRa "gateways" consisting of a single-board computer and a $4 LoRa module.

The goal of the project is to provide simple LoRa forwarder for:

• Linux - Orange Pi, Raspberry Pi, etc.
• Supports the Semtech UDP protocol v2 - uplink, downlink, and stats:
  • The Things Network - tested V2 and V3
  • ChirpStack - tested V3
• Supported LoRaWAN device classes:
  • class A , LoRa modulation - tested
• SPI communication based on wiringPi and modified RadioLib for Linux (Orange Pi or Raspberry PI) with LoRa chips:
  • SX126x series
  • LLCC68
  • SX127x series
  • RFM9x series
• Basic JSON configuration file

Along with network connection on your single-board computer (WiFi, Ethernet...) the following pins on your device have to be allocated:

• SPI module pins
  • MISO
  • MOSI
  • CLK
• 3 or 4 GPIO pins for connecting to the LoRa module:
  • CS (a.k.a NSS)
  • DIO 0
  • DIO 1
  • REST - optional
• power pins - 2 pins for VCC (usually 3.3V) and 1 for GND

Please refer to command gpio readall (also check the next sections) to obtain more information for your particular board. Look into the WiringPi numbers as well, because the configuration file expects that numbering scheme.

For e.g.:

  ------ ----- ---------- ------ --- OrangePiH3 --- ------ ---------- ----- ------ 
 | GPIO | wPi |   Name   | Mode | V | Physical | V | Mode | Name     | wPi | GPIO |
  ------ ----- ---------- ------ --- ----  ---- --- ------ ---------- ----- ------ 
 |      |     |     3.3v |      |   |  1 || 2  |   |      | 5v       |     |      |
 |   12 |   0 |    SDA.0 | ALT2 | 0 |  3 || 4  |   |      | 5V       |     |      |
 |   11 |   1 |    SCL.0 | ALT2 | 0 |  5 || 6  |   |      | 0v       |     |      |
 |    6 |   2 |      PA6 |  OFF | 0 |  7 || 8  | 0 | OFF  | TxD3     | 3   | 13   |
 |      |     |       0v |      |   |  9 || 10 | 0 | OFF  | RxD3     | 4   | 14   |
 |    1 |   5 |     RxD2 |  OFF | 0 | 11 || 12 | 1 | OUT  | PD14     | 6   | 110  |
 |    0 |   7 |     TxD2 |  OFF | 1 | 13 || 14 |   |      | 0v       |     |      |
 |    3 |   8 |     CTS2 |  OFF | 0 | 15 || 16 | 0 | IN   | PC04     | 9   | 68   |
 |      |     |     3.3v |      |   | 17 || 18 | 1 | IN   | PC07     | 10  | 71   |
 |   64 |  11 |     MOSI | ALT3 | 0 | 19 || 20 |   |      | 0v       |     |      |
 |   65 |  12 |     MISO | ALT3 | 0 | 21 || 22 | 0 | OFF  | RTS2     | 13  | 2    |
 |   66 |  14 |     SCLK | ALT3 | 0 | 23 || 24 | 0 | ALT3 | CE0      | 15  | 67   |
 |      |     |       0v |      |   | 25 || 26 | 0 | OFF  | PA21     | 16  | 21   |
 |   19 |  17 |    SDA.1 | ALT3 | 0 | 27 || 28 | 0 | ALT3 | SCL.1    | 18  | 18   |
 |    7 |  19 |     PA07 |  OFF | 0 | 29 || 30 |   |      | 0v       |     |      |
 |    8 |  20 |     PA08 |  OFF | 0 | 31 || 32 | 0 | OFF  | RTS1     | 21  | 200  |
 |    9 |  22 |     PA09 |  OFF | 0 | 33 || 34 |   |      | 0v       |     |      |
 |   10 |  23 |     PA10 |  OFF | 0 | 35 || 36 | 0 | OFF  | CTS1     | 24  | 201  |
 |   20 |  25 |     PA20 |  OFF | 0 | 37 || 38 | 0 | OFF  | TxD1     | 26  | 198  |
 |      |     |       0v |      |   | 39 || 40 | 0 | OFF  | RxD1     | 27  | 199  |
 |    4 |  28 |     PA04 | ALT2 | 0 | 41 || 42 | 0 | ALT2 | PA05     | 29  | 5    |
  ------ ----- ---------- ------ --- ----  ---- --- ------ ---------- ----- ------ 
 | GPIO | wPi |   Name   | Mode | V | Physical | V | Mode | Name     | wPi | GPIO |
  ------ ----- ---------- ------ --- OrangePiH3 --- ------ ---------- ----- ------ 

   ___
   \_/     SX1278  module
    |      --------------
     \--- | ANT      GND |===== Pin #20 [OrangePiH3 Physical]
          | GND     DIO1 |===== Pin #18 [OrangePiH3 Physical] / [a.k.a WiringPi pin ## 10]
          |         DIO2 |
          |         DIO3 |
          |          VCC |===== Pin # 1 [OrangePiH3 Physical]
          |         MISO |===== Pin #21 [OrangePiH3 Physical] / [[a.k.a WiringPi pin ## 12]]
          |         MOSI |===== Pin #19 [OrangePiH3 Physical] / [[a.k.a WiringPi pin ## 11]]
          |         SLCK |===== Pin #23 [OrangePiH3 Physical] / [[a.k.a WiringPi pin ## 14]]
          |          NSS |===== Pin #12 [OrangePiH3 Physical] / [a.k.a WiringPi pin ## 6]
          |         DIO0 |===== Pin #16 [OrangePiH3 Physical] / [a.k.a WiringPi pin ## 9]
          |         REST |===== optional, if it isn't used leave floating or connect to VCC
          |          GND |
           --------------

git clone --recurse-submodules https://github.com/zhgzhg/LoRaPacketForwarder.git

The following steps have been tested on Armbian v5.90. However it is recommended to use its latest version.

• Compile wiringPi for Orange PI //for the ZERO model use WiringOP-Zero library instead// with ./build command
  • Optionally specify the PLATFORM variable to change the board config (for e.g. for Orange Pi PC: PLATFORM=orangepipc ./build) or leave the build script to determine it automatically.
  • On Armbian and Orange PI you might need to add the spi-spidev overlay. Additionally in /boot/armbianEnv.txt you'll need to add parameter param_spidev_spi_bus=1 or param_spidev_spi_bus=0 depending on the board model. For e.g.:
    • Orange PI Zero - param_spidev_spi_bus=1 if we consider the the following active overlays: i2c0 i2c1 pps-gpio pwm spi-add-cs1 spi-spidev uart1 usbhost2 usbhost3
    • Orange PI PC - param_spidev_spi_bus=0
    • For more information check https://docs.armbian.com/User-Guide_Allwinner_overlays/, https://github.com/armbian/sunxi-DT-overlays/blob/master/sun8i-h3/README.sun8i-h3-overlays) , and consult with the board's specific docs
    • Warning : On some newer Linux Kernels (for e.g. > 5.10.43-sunxi) depending on the board model the SPI may not work at all. Indication of that may be the missing /dev/spidev* directory despite the loaded spidev driver. A temporary workaround for this case is switching to an older kernel.
    • Warning 2 : Variations in the loaded overlays even for the same board will produce different results for the available GPIO pins, SPI devices, etc! The gpio readall command will also show a slightly different table, having some rows hidden or shown.
  • Execute gpio readall to see the board pinout scheme table
• Compile this project with make

• WiringPi is pre-installed on Raspbian - no actions needed
• Compile this project with make

• Create config.json by copying config.json.template:

  • Edit the spi_port and spi_channel values accordingly.
    • Consult the MISO / MOSI and in particular ".number" postfixes of the gpio readall command
    • Additionally observe the output of sudo ls /dev/spi* where results like for e.g. "/dev/spidev1.0" correspond to /dev/spidev<spiChannelNumber>.<spiPortNumer>
    • Note that the ability to specify custom spi_port is a non-standard feature, which may not work on environments with the original wiringPi for RaspberryPi. An alternative solution is creating symlinks to /dev/spidev<x>.<x>.
  • Edit the ic_model field to specify the LoRa chip model. Use one of the following supported values below:
    • For SX126x series: SX1261, SX1262, or SX1268
    • For LLCC68: LLCC68
    • For SX127x series: SX1272, SX1273, SX1276, SX1277, SX1278, or SX1279
    • For RFM9x series: RFM95, RFM96, RFM97, or RFM98
  • Edit the pinout (execute gpio readall to check wiringPi pin numbers that need to be specified). Please note that pin_rest is optional. If it isn't used you should set it to -1 and leave the transceiver's pin floating or connected to VCC;
  • Edit the remaining parameters accordingly.

• To execute the application:

  • ./LoRaPktFwrd

• To execute the application and also specify network interface used for ID generation:

  • ./LoRaPktFwrd <interface_name>
    • The default one is eth0
    • Example: ./LoRaPktFwrd wlan0

• To get the supported CLI options:

  • ./LoRaPktFwrd -h

This project can be installed as a Systemd service (refer to file LoRaPktFwrd.service) which optionally may start automatically after the system boots. As a prerequisite make sure the project is compiled (via the make command) and it is able to execute correctly with your own config.json file.

• To install the LoRaPktFwrd service you can execute: sudo make install
• To uninstall the service use: sudo make uninstall
• To allow the service to run automatically after the system boots: sudo systemctl enable LoRaPktFwrd.service
• To disallow the service to run automatically after the system boots: sudo systemctl disable LoRaPktFwrd.service
• To manually start / restart/ stop / check the status of the service:

sudo service LoRaPktFwrd start
sudo service LoRaPktFwrd restart
sudo service LoRaPktFwrd stop
sudo service LoRaPktFwrd status

• To inspect the latest logs of the service: sudo journalctl -n 100 -f -u LoRaPktFwrd.service

LoRa UDP Packet Forwarder relies on the following programs and libraries:

• g supporting C 14 standard
• make
• WiringPi

Provided is a simple LoRa trasmitter example Arduino project called "Transmit" in the current directory. Hook your ESP8266/Arduino/whatever board via SPI to SX1278 module, compile it, and it will start transmitting data. Using the default configuration inside "config.json.template" in terms of RF specs, the forwarder app should immediately pick data from the transmitter.

A tiny temperature monitor program that can run in the background and modify GPIO pins in response.

Achieving a perfect downlink transmission timings appears to be difficult with the combination of an ordinary single-board computer equipped with a plain LoRa transceiver. The reason for that comes down to the imprecise hardware clock of the computer combined with the non-real time nature of Linux. To compensate for it this project aims running with a very high (nearly real time) priority, and increased CPU usage (roughly 20%) to partially make up for the irregular OS delays.

https://github.com/jgromes/RadioLib

https://github.com/adafruit/single_chan_pkt_fwd

https://github.com/orangepi-xunlong/wiringOP

https://github.com/xpertsavenue/WiringOP-Zero

https://github.com/Lora-net/packet_forwarder

https://www.gw-openscience.org/static/js/gpstimeutil.js

https://github.com/Tencent/rapidjson