A complete userspace implementation of WireGuard written in Golang for OpenWRT-based devices that do not have kernel support for WireGuard. If your device does have kernel support for WireGuard, then you should not be using this.
The implementation is optimised for minimum memory use. It should only consume around 20Mb of RAM for each WireGuard interface.
For more information on WireGuard, please see https://www.wireguard.com/.
The device firmware MUST have kernel TUN support. You can verify whether your kernel has TUN configured with the following command:
zcat /proc/config.gz | grep CONFIG_TUN
If this command returns CONFIG_TUN=y, then you can use this implementation. If it returns # CONFIG_TUN is not set, you cannot.
An opkg repository is available for arm-cortex-a9 architecture devices.
Run the following commands to configure opkg correctly:
grep -qE 'arch\s*\barm_cortex-a9\b' /etc/opkg.conf || echo 'arch arm_cortex-a9 10' >> /etc/opkg.conf
grep -q '/openwrt-wireguard-go/' /etc/opkg/customfeeds.conf || echo 'src/gz wg_go https://raw.githubusercontent.com/seud0nym/openwrt-wireguard-go/master/repository/arm_cortex-a9/base' >> /etc/opkg/customfeeds.conf
To install or upgrade, run the following commands:
opkg update
opkg install wireguard-go
Run the following command to download and install the correct release for your device:
curl -skL https://raw.githubusercontent.com/seud0nym/openwrt-wireguard-go/master/install_arm.sh | sh -s --
The script will determine the correct version for your processor. This may mean, for example, that even though your device has an ARMv7 processor, the ARMv5 release may be selected, as some versions of the ARMv7 chip do not have a Floating Point Unit which will cause the ARMv7 release to core dump.
If opkg is configured correctly with an architecture of arm-cortex-a9 specified in the /etc/opkg.conf file, then the latest release .ipk file will be downloaded and installed with the opkg command. Otherwise, the appropriate release tar file will be downloaded and extracted to the correct locations.
If you are uncomfortable running the script without reviewing it first, simply download it and execute it manually:
curl -skLO https://raw.githubusercontent.com/seud0nym/openwrt-wireguard-go/master/install_arm.sh
chmod x install_arm.sh
./install_arm.sh
This requires an installation of go ≥ 1.16.
git clone https://github.com/seud0nym/openwrt-wireguard-go.git
cd openwrt-wireguard-go
./build.sh [<ARCH> ...|all]
The build.sh script will by default build the release .tgz files for the ARM architecture. You can specify one or more valid GOARCH architectures (separated by spaces) or all to build all releases.
To install the release on a device, execute:
tar -zxvf openwrt-wireguard-go_<ARCH>.tgz -C /
sysctl -e -p /etc/sysctl.d/99-wireguard.conf
Please note that only the ARMv5 version has been tested.
Once installed, you can use the official OpenWRT guides at https://openwrt.org/docs/guide-user/services/vpn/wireguard/start to configure WireGuard as a server and/or a client.
However, do NOT install the specified opkg packages (wireguard and wireguard-tools). If your device does not have kernel support for WireGuard, then the installation of the wireguard package will probably fail. The wireguard-tools package may work, but it is unnecessary as this project includes all the required files, and the wireguard-tools package will replace some or all of them, causing everything to break.
If your device does have kernel support for WireGuard, then you should not be using this. If you just need an implementation of the WireGuard wg(8) utility, then have a look at wg-go.
Remove any network configurations you have created, then:
opkg remove wireguard-go
wg --uninstall
This project would not be possible without the official WireGuard cross-platform repositories: