Jump to content

Frame rate

From Wikipedia, the free encyclopedia
(Redirected from Frame rates)

Frame rate, most commonly expressed in frames per second or FPS, is typically the frequency (rate) at which consecutive images (frames) are captured or displayed. This definition applies to film and video cameras, computer animation, and motion capture systems. In these contexts, frame rate may be used interchangeably with frame frequency and refresh rate, which are expressed in hertz. Additionally, in the context of computer graphics performance, FPS is the rate at which a system, particularly a GPU, is able to generate frames, and refresh rate is the frequency at which a display shows completed frames.[1] In electronic camera specifications frame rate refers to the maximum possible rate frames could be captured, but in practice, other settings (such as exposure time) may reduce the actual frequency to a lower number than the frame rate.

Human vision

[edit]

The temporal sensitivity and resolution of human vision varies depending on the type and characteristics of visual stimulus, and it differs between individuals. The human visual system can process 10 to 12 images per second and perceive them individually, while higher rates are perceived as motion.[2] Modulated light (such as a computer display) is perceived as stable by the majority of participants in studies when the rate is higher than 50 Hz. This perception of modulated light as steady is known as the flicker fusion threshold. However, when the modulated light is non-uniform and contains an image, the flicker fusion threshold can be much higher, in the hundreds of hertz.[3] With regard to image recognition, people have been found to recognize a specific image in an unbroken series of different images, each of which lasts as little as 13 milliseconds.[4] Persistence of vision sometimes accounts for very short single-millisecond visual stimulus having a perceived duration of between 100 ms and 400 ms. Multiple stimuli that are very short are sometimes perceived as a single stimulus, such as a 10 ms green flash of light immediately followed by a 10 ms red flash of light perceived as a single yellow flash of light.[5]

Film and video

[edit]

Silent film

[edit]

Early silent films had stated frame rates anywhere from 16 to 24 frames per second (fps),[6] but since the cameras were hand-cranked, the rate often changed during the scene to fit the mood. Projectionists could also change the frame rate in the theater by adjusting a rheostat controlling the voltage powering the film-carrying mechanism in the projector.[7] Film companies often intended that theaters show their silent films at higher frame rates than they were filmed at.[8] These frame rates were enough for the sense of motion, but it was perceived as jerky motion. To minimize the perceived flicker, projectors employed dual- and triple-blade shutters, so each frame was displayed two or three times, increasing the flicker rate to 48 or 72 hertz and reducing eye strain. Thomas Edison said that 46 frames per second was the minimum needed for the eye to perceive motion: "Anything less will strain the eye."[9][10] In the mid to late 1920s, the frame rate for silent film increased to 20–26 FPS.[9]

Sound film

[edit]

When sound film was introduced in 1926, variations in film speed were no longer tolerated, as the human ear is more sensitive than the eye to changes in frequency. Many theaters had shown silent films at 22 to 26 FPS, which is why the industry chose 24 FPS for sound film as a compromise.[11] From 1927 to 1930, as various studios updated equipment, the rate of 24 FPS became standard for 35 mm sound film.[2] At 24 FPS, the film travels through the projector at a rate of 456 millimetres (18.0 in) per second. This allowed simple two-blade shutters to give a projected series of images at 48 per second, satisfying Edison's recommendation. Many modern 35 mm film projectors use three-blade shutters to give 72 images per second—each frame is flashed on screen three times.[9]

Animation

[edit]
This animated cartoon of a galloping horse is displayed at 12 drawings per second, and the fast motion is on the edge of being objectionably jerky.

In drawn animation, moving characters are often shot "on twos", that is to say, one drawing is shown for every two frames of film (which usually runs at 24 frame per second), meaning there are only 12 drawings per second.[12] Even though the image update rate is low, the fluidity is satisfactory for most subjects. However, when a character is required to perform a quick movement, it is usually necessary to revert to animating "on ones", as "twos" are too slow to convey the motion adequately. A blend of the two techniques keeps the eye fooled without unnecessary production cost.[13]

Animation for most "Saturday morning cartoons" was produced as cheaply as possible and was most often shot on "threes" or even "fours", i.e. three or four frames per drawing. This translates to only 8 or 6 drawings per second respectively. Anime is also usually drawn on threes or twos.[14][15]

Modern video standards

[edit]

Due to the mains frequency of electric grids, analog television broadcast was developed with frame rates of 50 Hz (most of the world) or 60 Hz (Canada, US, Mexico, Philippines, Japan, South Korea). The frequency of the electricity grid was extremely stable and therefore it was logical to use for synchronization.

The introduction of color television technology made it necessary to lower that 60 FPS frequency by 0.1% to avoid "dot crawl", a display artifact appearing on legacy black-and-white displays, showing up on highly-color-saturated surfaces. It was found that by lowering the frame rate by 0.1%, the undesirable effect was minimized.

As of 2021, video transmission standards in North America, Japan, and South Korea are still based on 60  / 1.001 ≈ 59.94 images per second. Two sizes of images are typically used: 1920×1080 ("1080i/p") and 1280×720 ("720p"). Confusingly, interlaced formats are customarily stated at 1/2 their image rate, 29.97/25 FPS, and double their image height, but these statements are purely custom; in each format, 60 images per second are produced. A resolution of 1080i produces 59.94 or 50 1920×540 images, each squashed to half-height in the photographic process and stretched back to fill the screen on playback in a television set. The 720p format produces 59.94/50 or 29.97/25 1280×720p images, not squeezed, so that no expansion or squeezing of the image is necessary. This confusion was industry-wide in the early days of digital video software, with much software being written incorrectly, the developers believing that only 29.97 images were expected each second, which was incorrect. While it was true that each picture element was polled and sent only 29.97 times per second, the pixel location immediately below that one was polled 1/60 of a second later, part of a completely separate image for the next 1/60-second frame.

At its native 24 FPS rate, film could not be displayed on 60 Hz video without the necessary pulldown process, often leading to "judder": To convert 24 frames per second into 60 frames per second, every odd frame is repeated, playing twice, while every even frame is tripled. This creates uneven motion, appearing stroboscopic. Other conversions have similar uneven frame doubling. Newer video standards support 120, 240, or 300 frames per second, so frames can be evenly sampled for standard frame rates such as 24, 48 and 60 FPS film or 25, 30, 50 or 60 FPS video. Of course these higher frame rates may also be displayed at their native rates.[16][17]

Electronic camera specifications

[edit]

In electronic camera specifications frame rate refers to the maximum possible rate frames that can be captured (e.g. if the exposure time were set to near-zero), but in practice, other settings (such as exposure time) may reduce the actual frequency to a lower number than the frame rate.[18]

Frame rate up-conversion

[edit]

Frame rate up-conversion (FRC) is the process of increasing the temporal resolution of a video sequence by synthesizing one or more intermediate frames between two consecutive frames. A low frame rate causes aliasing, yields abrupt motion artifacts, and degrades the video quality. Consequently, the temporal resolution is an important factor affecting video quality. Algorithms for FRC are widely used in applications, including visual quality enhancement, video compression and slow-motion video generation.

Low frame rate video
Video with 4 times increased frame rate

Methods

[edit]

Most FRC methods can be categorized into optical flow or kernel-based[19][20] and pixel hallucination-based methods.[21][22]

Flow-based FRC

[edit]

Flow-based methods linearly combines predicted optical flows between two input frames to approximate flows from the target intermediate frame to the input frames. They also propose flow reversal (projection) for more accurate image warping. Moreover, there are algorithms that gives different weights of overlapped flow vectors depending on the object depth of the scene via a flow projection layer.

Pixel hallucination-based FRC

[edit]

Pixel hallucination-based methods use deformable convolution to the center frame generator by replacing optical flows with offset vectors. There are algorithms that also interpolates middle frames with the help of deformable convolution in the feature domain. However, since these methods directly hallucinate pixels unlike the flow-based FRC methods, the predicted frames tend to be blurry when fast-moving objects are present.

See also

[edit]

References

[edit]
  1. ^ Tamasi, Tony (3 December 2019). "What is Frame Rate and Why is it Important to PC Gaming?". Retrieved 12 February 2023.
  2. ^ a b Read, Paul; Meyer, Mark-Paul; Gamma Group (2000). Restoration of motion picture film. Conservation and Museology. Butterworth-Heinemann. pp. 24–26. ISBN 978-0-7506-2793-1.
  3. ^ James Davis (1986), "Humans perceive flicker artefacts at 500 Hz", Sci. Rep., 5: 7861, doi:10.1038/srep07861, PMC 4314649, PMID 25644611
  4. ^ Potter, Mary C. (December 28, 2013). "Detecting meaning in RSVP at 13 ms per picture" (PDF). Attention, Perception, & Psychophysics. 76 (2): 270–279. doi:10.3758/s13414-013-0605-z. hdl:1721.1/107157. PMID 24374558. S2CID 180862. Archived (PDF) from the original on 2022-10-09.
  5. ^ Robert Efron (1973). "Conservation of temporal information by perceptual systems". Perception & Psychophysics. 14 (3): 518–530. doi:10.3758/bf03211193.
  6. ^ Brown, Julie (2014). "Audio-visual Palimpsests: Resynchronizing Silent Films with 'Special' Music". In David Neumeyer (ed.). The Oxford Handbook of Film Music Studies. Oxford University Press. p. 588. ISBN 978-0195328493.
  7. ^ Kerr, Walter (1975). Silent Clowns. Knopf. p. 36. ISBN 978-0394469072.
  8. ^ Card, James (1994). Seductive cinema: the art of silent film. Knopf. p. 53. ISBN 978-0394572185.
  9. ^ a b c Brownlow, Kevin (Summer 1980). "Silent Films: What Was the Right Speed?". Sight & Sound. 49 (3): 164–167. Archived from the original on 8 July 2011. Retrieved 2 May 2012.
  10. ^ Elsaesser, Thomas; Barker, Adam (1990). Early cinema: space, frame, narrative. BFI Publishing. p. 284. ISBN 978-0-85170-244-5.
  11. ^ TWiT Netcast Network (2017-03-30), How 24 FPS Became Standard, archived from the original on 2021-11-04, retrieved 2017-03-31
  12. ^ Chew, Johnny. "What Are Ones, Twos, and Threes in Animation?". Lifewire. Retrieved August 8, 2018.
  13. ^ Whitaker, Harold; Sito, John Halas; updated by Tim (2009). Timing for animation (2nd ed.). Amsterdam: Elsevier/Focal Press. p. 52. ISBN 978-0240521602. Retrieved August 8, 2018.{{cite book}}: CS1 maint: multiple names: authors list (link)
  14. ^ "Shot on threes (ones, twos, etc.)". Anime News Network.
  15. ^ CLIP STUDIO (12 February 2016). "CLIP STUDIO PAINT アニメーション機能の使い方". Archived from the original on 2021-11-04 – via YouTube.
  16. ^ High Frame-Rate Television, BBC White Paper WHP 169, September 2008, M. Armstrong, D. Flynn, M. Hammond, PAWAN Jahajpuria S. Jolly, R. Salmon.
  17. ^ Jon Fingas (November 27, 2014), "James Cameron's 'Avatar' sequels will stick to 48 frames per second", Engadget, retrieved April 15, 2017
  18. ^ Whaley, Sean (21 November 2018). "What is Frame Rate and Why is it Important to PC Gaming?". Retrieved 5 August 2021.
  19. ^ Simon, Niklaus; Long, Mai; Feng, Liu (2017). Video frame interpolation via adaptive separable convolution. ICCV. arXiv:1708.01692.
  20. ^ Huaizu, Jiang; Deqing, Sun; Varun, Jampani; Ming-Hsuan, Yang; Erik, Learned-Miller; Jan, Kautz (2018). Super slomo: High quality estimation of multiple intermediate frames for video interpolation. ICCV. arXiv:1712.00080.
  21. ^ Shurui, Gui; Chaoyue, Wang; Qihua, Chen; Dacheng, Tao (2020). "Featureflow: Robust video interpolation via structure-to-texture generation". 2020 IEEE/CVF Conference on Computer Vision and Pattern Recognition (CVPR). IEEE. pp. 14001–14010. doi:10.1109/CVPR42600.2020.01402. ISBN 978-1-7281-7169-2.
  22. ^ Myungsub, Choi; Heewon, Kim; Bohyung, Han; Ning, Xu; Kyoung, Mu Lee (2020). "Channel Attention is All You Need for Video Frame Interpolation". Proceedings of the AAAI Conference on Artificial Intelligence. 34 (7). AAAI: 10663–10671. doi:10.1609/aaai.v34i07.6693.
[edit]

(Wayback Machine copy)