Uberducky is a tool for injecting keystrokes into a target computer that can be triggered wirelessly via BLE. It is inspired by Hak5's USB Rubber Ducky, and like that tool it impersonates a USB keyboard and can inject malicious payloads such as reverse shells and RATs.
A normal USB Rubber Ducky has one major shortcoming: it is only useful when the target machine is left unlocked. An Uberducky can be hidden in a forgotten USB port, such as behind a tower under a desk or attached to a monitor. As soon as the operator of the target system drops their guard (or you distract them), Uberducky can be triggered to drop a malicious payload.
If you're interested you can read the story behind Uberducky and learn more about how it's built.
At the moment, you will need to build the firmware to use the tool and rebuild it any time you want to change the duckyscript payload.
You will need ubertooth-dfu from Project
Ubertooth to flash the
firmware. You will also need an ARM toolchain. If you are on Debian or Ubuntu,
install these with:
apt-get install gcc-arm-none-eabi libnewlib-arm-none-eabi
This repo uses a submodule. If you didn't git clone --recursive, you must
pull down the submodule using:
git submodule update --init --recursive
Drop your duckyscript payload into script.txt. You can then build and
flash the firmware by running:
make
ubertooth-dfu -r -d uberducky.dfu
Big fat warning: this will replace any existing Ubertooth firmware you have on the device. If you want to re-flash normal Ubertooth firmware, follow the instructions below for how to re-flash.
Uberducky will wait for a specially-formatted BLE advertising packet. When it receives this packet, it will run the duckyscript. There are two ways of triggering it. If you have a second Ubertooth, you can run the following:
ubertooth-ducky -q
If you do not have a second Ubertooth but you have a system running Linux, you can send the special packet using the following commands:
sudo btmgmt add-adv -D 1 -u fd123ff9-9e30-45b2-af0d-b85b7d2dc80c 1 &&
sudo btmgmt clr-adv
If neither of these approaches strikes your fancy, you may trigger Uberducky
using any mechanism that results in fd123ff9-9e30-45b2-af0d-b85b7d2dc80c being
in the first 32 bytes of any BLE advertising packet on channel 38 (2426 MHz) in
LE byte order (i.e., 0c c8 2d 7d...). We're simply advertising it in a list of
128-bit UUIDs.
Since Uberducky impersonates a keyboard, it does not respond to normal USB commands for reflashing the firmware. There are two mechanisms for forcing it to re-enter DFU mode and allowing the firmware to be re-flashed. The first is to send a specially-formatted BLE packet to reset it into DFU mode using a second Ubertooth:
ubertooth-ducky -b
It can also be done from Linux:
sudo btmgmt add-adv -D 1 -u 344bc7f2-5619-4953-9be8-9888fe29d996 1 &&
sudo btmgmt clr-adv
Alternatively, you can force the device into DFU mode by using a wire to jumper two pins on the expansion header.
The expansion header is a 2x3 pin header between the two largest chips on the board, about halfway between the USB connector and antenna. It is labeled "EXPAND" on the back side of the board. Holding the board so USB is pointed up, on the front side of the board the expansion header looks like this:
-------
6 O | O | 3
--- ---
5 O | O | 2
--- ---
4 O | X | 1
--- ---
PIN #1, marked X, is square.
With Ubertooth unplugged, use a piece of wire, paperclip, staple, etc to connect pins 1 and 2 together. When it it plugged in, the Ubertooth should enter bootloader mode (LEDs will be turning on and off in sequence).
You must flash the new firmware within 5 seconds, otherwise it will boot into the previously flashed firmware.
I would like to implement some mechanism for updating the Duckyscript and changing the UUID without having to recompile. Possible solutions include a USB serial port and a wireless protocol.
It would be useful to have dedicated apps for triggering Uberducky on OS X, Android, and possibly even iOS.
Sometimes it's not feasible to wait for your target to leave their computer unlocked. If their system has a hidden USB port (such as behind a screen or under a desk) you can plug in Uberducky and lay in wait. When the opportunity arises, distract the victim and launch the attack wirelessly.
Ubertooth is a great piece of kit, and best of all the design is completely open. The LPC1752 microcontroller has a flexible USB peripheral that can emulate a keyboard, and the CC2400 radio facilitates easy communication over 2.4 GHz ISM. This tool was partly an exercise in seeing how little code it takes to receive BLE advertising packets on Ubertooth (fewer than 100 lines of actual code!).
Update script.txt and rerun the make and ubertooth-dfu commands listed
above. We're working on better ways of doing this.
See the above section on "re-flashing firmware".
No comment (hey there are kids around).
Submit a GitHub issue with your feature request, or better yet a pull request :)
Uberducky was written by Mike Ryan of ICE9 Consulting. The author disclaims any liability for the illegal use of this tool.