10x10cm IBM PC compatible machine with 386 CPU, integrated VGA and sound.

More random photos: link

• M6117D System-On-Chip with integrated 386SX40 (almost compatible) CPU and M1217B chipset
• 4MB RAM
• TVGA9500i VGA video
• ES1868F SoundBlasterPro-compatible sound
• SAM2695 MIDI synthesizer
• ESP8266 WiFi module
• PS/2 keyboard and mouse inputs
• 2xCOM ports
• CF card slot
• Real-time clock (RTC) with backup battery
• Integrated PC-speaker
• 5.1V microUSB power
• Two 4-layer 10x10cm PCBs front/back panel PCB
• G738 or G706 enclosure

release/pcb_main.rev.A1.pdf - motherboard schematic and bill of materials
release/pcb_top.rev.A1.pdf - video&sound board schematic and bill of materials
release/bom_interactive_main.rev.A1.html - motherboard interactive BOM
release/bom_interactive_top.rev.A1.html - video&sound board interactive BOM
release/gerber_main.rev.A1.zip - motherboard fabrication files
release/gerber_top.rev.A1.zip - video&sound board fabrication files
release/gerber_covers.rev.A.zip - front and back panel fabrication files
roms/M6117 - award ami.bin - main BIOS image
roms/tvga9500i - D3.51 D4.01E.bin - VGA BIOS image
software/msdos622_compactflash_2GB.7z - CF card image with preinstalled MS-DOS 6.22 and all necessary drivers

There is two options how to use WiFi module:

1. Zimodem (link) - provides ability to connect to BBS via any terminal without using additional software. WiFi module is connected to COM4, so you can use any terminal to communicate with it using AT commands.
2. esp_slip_router (link) - provides ability to connect your machine to IP network just like as Ethernet. You need ETHERSLIP or similar packet driver for DOS.

To upload firmware you need USB-UART adapter with 3.3V signal levels. Connect GND, RX and TX lines to esp header located on main PCB at left, install BOOT/GND jumper and follow any ESP8266 firmware update guide that is available on the internet.

MIDI synthesizer is connected to the AUXB sound input of ES1868F. Usually this input named as "CD input" in mixer software.
PC speaker is connected to the AUXA input.
To obtain a minimum noise level, it is recommended to disable line input in the mixer.

Main PCB:

• Rev.A - first release. Please note the errata;
• Rev.A1 - fixed all rev.A issues; added switch for BIOS variant select; added optional -5V source. Please note the errata.

Top PCB:

• Rev.A - first release. Please note the errata;
• Rev.A1 - fixed all rev.A issues; added switch for VGA BIOS variant select; removed VGA-disable switch; added EEPROM for ES1868.

Covers PCB:

• Rev.A - first release.

I want to express my appreciation to the authors of the following projects, which served as inspiration and as reference for my development:

http://www.alexandrugroza.ro/microelectronics/system-design/isa-80386dx-sbmc/index.html - 80386DX ISA single board microcomputer by Alexandru Groza
https://bitbucket.org/Haper/poisk-2-mainboard/src/master/ - XT compatible 8086-based machine, reverse engineered by Andrew Khapoknysh (details)
http://www.malinov.com/Home/sergeys-projects/xi-8088 - IBM PC/XT compatible processor board in ISA board form factor by by Sergey Kiselev
https://github.com/skiselev/micro_8088 - IBM XT compatible processor board based on Faraday FE2010 chipset by Sergey Kiselev
https://github.com/monotech/NuXT - MicroATX Turbo XT Motherboard, with VGA, floppy, CF, serial by Monotech
http://www.malinov.com/Home/sergeys-projects/isa-supervga - ISA Super VGA card based on the Trident TVGA9500i Super VGA controller IC by Sergey Kiselev
https://github.com/monotech/PC104-SVGA - 8088-compatible 8-bit ISA PC/104 SVGA card by Monotech https://github.com/hkzlab/ES1868_ISA8 - ISA 8bit sound card based on the ES1868F sound chip by hkzlab