List of DIN standards

This is an incomplete list of DIN standards.

The "STATUS" column gives the latest known status of the standard.
- If a standard has been withdrawn and no replacement specification is listed, either the specification was withdrawn without replacement or a replacement specification could not be identified.
DIN stands for "Deutsches Institut für Normung", meaning "German institute for standardization". DIN standards that begin with "DIN V" ("Vornorm", meaning "pre-standard") are the result of standardization work, but because of certain reservations on the content or because of the divergent compared to a standard installation procedure of DIN, they are not yet published standards.

DIN 1 to DIN 999

DIN 1 to DIN 99

DIN	Title	Status	DIN replacement	Other org replacement
DIN 1	Cone Pins, untempered	Withdrawn	DIN EN 22339	ISO 2339
DIN 3	Standard measurements	Withdrawn
DIN 5	Technical drawings – Axonometric projections, Isometric projection	Withdrawn	DIN ISO 5456-1, DIN ISO 5456-2, DIN ISO 5456-3, DIN ISO 5456-4	ISO 5456-1, ISO 5456-2, ISO 5456-3, ISO 5456-4
DIN 5-10	Technical drawings – projections, terms	Withdrawn	DIN ISO 10209-2	ISO 10209-2
DIN 6	Projection displays in Normal, views and special presentations	Withdrawn	DIN ISO 128, DIN EN ISO 128	ISO 128
DIN 7	Parallel Pins	Withdrawn	DIN EN ISO 2338	ISO 2338
DIN 11	Whitworth pipe threads 1/4"-6" Thread diameter, sizes, teaching information	Withdrawn
DIN 13-1	ISO general purpose metric screw threads – Part 1: Nominal sizes for coarse pitch threads; nominal diameter from 1 mm to 68 mm	Active
DIN 13-2	ISO general purpose metric screw threads – Part 2: Nominal sizes for 0,2 mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mm	Active
DIN 13-3	ISO general purpose metric screw threads – Part 3: Nominal sizes for 0,5 mm fine pitch threads; nominal diameter from 3,5 mm to 90 mm	Active
DIN 13-4	ISO general purpose metric screw threads – Part 4: Nominal sizes for 0,75 mm fine pitch threads; nominal diameter from 5 mm to 110 mm	Active
DIN 13-5	ISO general purpose metric screw threads – Part 5: Nominal sizes for 1 mm and 1,25 mm fine pitch threads; nominal diameter from 7,5 mm to 200 mm	Active
DIN 13-6	ISO general purpose metric screw threads – Part 6: Nominal sizes for 1,5 mm fine pitch threads; nominal diameter from 12 mm to 300 mm	Active
DIN 13-7	ISO general purpose metric screw threads – Part 7: Nominal sizes for 2 mm fine pitch threads; nominal diameter from 17 mm to 300 mm	Active
DIN 13-8	ISO general purpose metric screw threads – Part 8: Nominal sizes for 3 mm fine pitch threads; nominal diameter from 28 mm to 300 mm	Active
DIN 13-9	ISO general purpose metric screw threads – Part 9: Nominal sizes for 4 mm fine pitch threads; nominal diameter from 40 mm to 300 mm	Active
DIN 13-10	ISO general purpose metric screw threads – Part 10: Nominal sizes for 6 mm fine pitch threads; nominal diameter from 70 mm to 500 mm	Active
DIN 13-11	ISO general purpose metric screw threads – Part 11: Nominal sizes for 8 mm fine pitch threads; nominal diameter from 130 mm to 1000 mm	Active
DIN 13-12	ISO general purpose metric screw threads – Part 12: 1 to 300 mm diameter coarse and fine pitch threads Selected diameters and pitches	Active
DIN 13-13	ISO general purpose metric screw threads – Part 13: Selected sizes for screws, bolts and nuts from 1 to 52 mm screw thread diameter and limits of sizes	Active
DIN 13-19	ISO general purpose metric screw threads – Part 19: Nominal profiles	Active
DIN 13-20	ISO general purpose metric screw threads – Part 20: Limits of sizes for coarse pitch threads with the preferred tolerance classes; nominal sizes from 1 mm to 68 mm	Active
DIN 13-21	ISO general purpose metric screw threads – Part 21: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 1 mm to 24,5 mm	Active
DIN 13-22	ISO general purpose metric screw threads – Part 22: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 25 mm to 52 mm	Active
DIN 13-23	ISO general purpose metric screw threads – Part 23: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 53 mm to 110 mm	Active
DIN 13-24	ISO general purpose metric screw threads – Part 24: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 112 mm to 180 mm	Active
DIN 13-25	ISO general purpose metric screw threads – Part 25: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 182 mm to 250 mm	Active
DIN 13-26	ISO general purpose metric screw threads – Part 26: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 252 mm to 1000 mm	Active
DIN 13-28	ISO general purpose metric screw threads – Part 28: Coarse and Fine Screw Threads from 1 to 250 mm Screw Thread Diameter; Root Cross-sections, Tensile Stress Cross-sections and Pitch Angles	Active
DIN 13-50	ISO general purpose metric screw threads – Part 50: Combination of tolerance classes for formed internal screw threads	Active
DIN 13-51	ISO general purpose metric screw threads – Part 51: External screw threads for transition fits (former: screw threads for interference fit); tolerances, limit deviations, limits of sizes	Active
DIN 13-52	ISO general purpose metric screw threads – Part 52: Multi-start thread tolerances and deviation of profile	Active
DIN 15-2	Technical drawings; lines; general application	Withdrawn	DIN ISO 128-24
DIN 16	Oblique Standard Typeface for Drawings	Withdrawn
DIN 17	Upright Standard Typeface for Drawings	Withdrawn
DIN 38	Plain bearings; bearing metal lining for thick-walled multilayer plain bearings	Active
DIN 74	Countersinks for countersunk head screws (except screws with DIN EN 27721 head)	Active
DIN 76-1	Thread run-outs and thread undercuts for ISO metric threads in accordance with DIN 13-1	Active
DIN 76-2	Thread run-outs and thread undercuts for pipe threads conforming to ISO 228 part 1	Active
DIN 76-3	Runouts, Undercuts for Trapezoidal Threads, Buttress Threads and Knuckle Threads and other Threads of Coarse Pitch	Active
DIN 78	Protrusions of bolt ends	Active	DIN EN ISO 4753 (governs thread ends for bolts assembled with hexagon slotted nuts)	ISO 4753
DIN 84	Product grade A slotted cheese head screws	Withdrawn	DIN EN ISO 1207	ISO 1207
DIN 85	Product grade A slotted pan head screws	Withdrawn	DIN EN ISO 1580	ISO 1580
DIN 88	Product slotted oval head countersunk machine screws	Withdrawn	ISO 2010-1983^[1]
DIN 93	Tab washers with long tab	Withdrawn
DIN 94	Split pins	Withdrawn	DIN EN ISO 1234	ISO 1234
DIN 95	Slotted Raised Countersunk (Oval) Head Wood Screws	Active
DIN 96	Slotted Round Head Wood Screws	Active

DIN 100 to DIN 199

DIN	Title	Status	DIN replacement	Other org replacement
DIN 101	Rivets – Technical specifications	Active
DIN 103-1	ISO Metric Trapezoidal Screw Thread; Profiles	Active
DIN 103-2	ISO Metric Trapezoidal Screw Thread; General Plan	Active
DIN 103-3	ISO Metric Trapezoidal Screw Thread; Allowances and Tolerances for Trapezoidal Screw Threads of General Purpose	Active
DIN 103-4	ISO Metric Trapezoidal Screw Thread; Nominal Dimensions	Active
DIN 103-5	ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 8 to 100 mm Nominal Diameter	Active
DIN 103-6	ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Nut Threads from 105 to 300 mm Nominal Diameter	Active
DIN 103-7	ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 8 to 100 mm Nominal Diameter	Active
DIN 103-8	ISO Metric Trapezoidal Screw Threads; Limiting Sizes for Bolt Threads from 105 to 300 mm Nominal Diameter	Active
DIN 103-9	ISO metric trapezoidal screw threads; gauging of external and internal threads; gauge dimensions and design features	Active
DIN V 105-1	Clay masonry units – Part 1: Solid and hollow bricks with density classes of 1,2	Withdrawn	DIN V 105-100, DIN EN 771-1	EN 771-1
DIN V 105-2	Clay masonry units – Part 2: Solid and hollow bricks with density classes equal 1.0	Withdrawn	DIN V 105-100, DIN EN 771-1	EN 771-1
DIN 105-3	Clay masonry units – Part 3: Tile and high strength-high-strength clinker	Withdrawn	DIN V 105-100, DIN EN 771-1	EN 771-1
DIN 105-4	Clay masonry units – Part 4: Ceramic bricks	Withdrawn	DIN V 105-100, DIN EN 771-1, DIN EN 772-7	EN 771-1, EN 772-7
DIN 105-5	Clay masonry units – Part 5: Lightweight long-hole brick and light long-hole brick panels	Active
DIN V 105-6	Clay masonry units – Part 6: High precision units	Active
DIN V 105-100	Clay masonry units – Part 100: Clay masonry units with specific properties	Active
DIN 125	Washers; medium type, primarily for hexagon bolts	Withdrawn	DIN EN ISO 7089, DIN EN ISO 7090	ISO 7089, ISO 7090
DIN 125-1	Product grade A washers – with a hardness up to 250 HV designed for use with hexagon head bolts and nuts	Withdrawn	DIN EN ISO 7089, DIN EN ISO 7090	ISO 7089, ISO 7090
DIN 125-2	Product grade A washers – with a hardness up to 300 HV designed for use with hexagon head bolts and nuts	Withdrawn	DIN EN ISO 7089, DIN EN ISO 7090	ISO 7089, ISO 7090
DIN 126	Product grade C washers – designed for use with hexagon head bolts and nut	Withdrawn	DIN EN ISO 7091	ISO 7091
DIN 127	Spring lock washers with square ends or tang ends	Withdrawn
DIN 128	Curved and wave spring lock washers	Withdrawn
DIN 137	Spring washers, curved or wave	Withdrawn
DIN 174	Bright Flat Steel; Dimensions, Permissible Variations, Weights	Withdrawn	DIN EN 10278
DIN 175	Polished round steel; Dimensions, Permissible deviations according to ISO tolerance zone h9	Withdrawn	DIN EN 10278

DIN 200 to DIN 299

DIN	Title	Status	DIN replacement	Other org replacement
DIN 201	Technical drawings; Hatchings; Representation of cutting edges and materials	Withdrawn	DIN ISO 128-50	ISO 128-50
DIN 209	Machine Reamers with Screwed-on Blades	Active
DIN 267-1	Fasteners – Part 1: Technical delivery conditions; General requirements	Withdrawn		ISO 8992
DIN 267-2	Fasteners – Part 2: Technical delivery conditions; Bolts, Screws, Nuts and Similar Threaded and Formed Parts; Types and Dimensional Accuracy	Active	DIN EN ISO 4759-1	ISO 4759-1
DIN 267-3	Fasteners – Part 3: Technical delivery conditions; Property classes for carbon steel and alloy steel bolts and screws; Conversion of property classes	Withdrawn	DIN EN ISO 898-1	ISO 898-1
DIN 267-4	Fasteners – Part 4: Technical delivery conditions; Property classes for nuts (previous classes)	Withdrawn	DIN EN ISO 898-2	ISO 898-2
DIN 267-5	Fasteners – Part 5: Technical delivery conditions; Acceptance inspection; modified version of ISO 3269, 1984 edition	Withdrawn	DIN EN ISO 3269	ISO 3269
DIN 267-6	Fasteners – Part 6: Technical delivery conditions; Designs and accuracy of measurement for product grade F	Active
DIN 267-7	Fasteners – Part 9: Technical delivery conditions; Bolts made of unalloyed or low-alloy steels	Withdrawn	DIN EN ISO 898-1	ISO 898-1
DIN 267-9	Fasteners – Part 9: Technical delivery conditions; Components with Electroplated Coatings	Withdrawn	DIN EN ISO 4042	ISO 4042
DIN 267-10	Fasteners – Part 10: Technical delivery conditions; Hot dip galvanized parts	Withdrawn	DIN EN ISO 10684	ISO 10684
DIN 267-11	Fasteners – Part 11: Technical delivery conditions (with additions to ISO 3506); Corrosion-resistant stainless steel fasteners	Withdrawn
DIN 267-12	Fasteners – Part 12: Technical delivery conditions; Self-tapping screws	Withdrawn	DIN EN ISO 2702	ISO 2702
DIN 267-13	Fasteners – Part 13: Technical delivery conditions; Components for Bolted Connections Made Mainly from Materials Exhibiting a High Impact Strength at Low Temperature or from Materials with a High Temperature Strength	Active
DIN 267-15	Fasteners – Part 15: Technical delivery conditions; Prevailing torque type nuts	Withdrawn	DIN EN ISO 2320, DIN EN ISO 3506-1, DIN EN ISO 3506-2, DIN EN ISO 3506-3	ISO 2320, ISO 3506-1, ISO 3506-2, ISO 3506-3
DIN 267-18	Fasteners – Part 18: Technical delivery conditions; Components made of Non-ferrous Metals	Withdrawn	DIN EN 28839	ISO 8839
DIN 267-19	\| Withdrawn	DIN EN ISO 26157-1, DIN EN ISO 26157-3	ISO 6157-1, ISO 6157-3
DIN 267-20	Fasteners – Part 20: Technical delivery conditions; Surface discontinuities on nuts	Withdrawn	DIN EN ISO 6157-2, DIN EN ISO 10484, DIN EN ISO 10485	ISO 6157-2, ISO 10484, ISO 10485
DIN 267-21	Fasteners – Part 21: Technical delivery conditions; Widening test on nuts	Withdrawn	DIN EN ISO 6157-2, DIN EN ISO 10484, DIN EN ISO 10485	ISO 6157-2, ISO 10484, ISO 10485
DIN 267-23	Fasteners – Part 23: Technical delivery conditions; Property classes for nuts with fine thread (ISO classes)	Withdrawn	DIN EN ISO 898-6	ISO 898-6
DIN 267-24	Fasteners – Part 24: Technical delivery conditions; Property classes for nuts (Hardness classes)	Active
DIN 267-25	Fasteners – Part 25: Technical delivery conditions; Torsion testing of M1 to M10 bolts and screws	Withdrawn	DIN EN 20898-7	EN 20898-7
DIN 267-26	Fasteners – Part 26: Technical delivery conditions; Conical spring washers for bolt/nut assemblies	Active
DIN 267-27	Fasteners – Part 27: Technical specifications; Steel screws, bolts and studs with adhesive coating	Active
DIN 267-28	Fasteners – Part 28: Technical specifications; Steel screws, bolts and studs with locking coating	Active
DIN 267-29	Fasteners – Part 29: Technical specifications; Product grades for parts for bolted connections for use at temperatures ranging from −200 °C to 700 °C	Withdrawn
DIN 267-30	Fasteners – Part 30: Technical specifications; Metric thread rolling screws of property class 10.9	Active
DIN 276-1	Building costs; Part 1: Building construction	Active
DIN 276-2	Building costs; Part 2: Classification of cost	Withdrawn
DIN 276-3	Building costs; Part 3: Ascertainment of cost	Withdrawn

DIN 300 to DIN 399

DIN	Title	Status	DIN replacement	Other org replacement
DIN 315	Wing nuts with rounded wings	Active
DIN 316	Wing screws with rounded wings	Active
DIN 317	Drill drifts for taper shanks with drift tang	Active
DIN 323-1	Preferred Numbers and Series of Preferred Numbers; Basic Values, Calculated Values, Rounded Values	Withdrawn
DIN 323-2	Preferred Numbers and Series of Preferred Numbers; Introduction	Active
DIN 332-1	60° centre holes; types R, A, B, and C	Active
DIN 332-2	Center holes 60° with thread for shaft ends for rotating electrical machines	Active
DIN 332-4	Centre holes for rail vehicles axles	Active
DIN 332-7	Machine tools; 60° centre holes; dimensioning	Active
DIN 332-8	Centre holes 90°, form S; dimensions, determination process	Active
DIN 332-10	Center Holes; Indications on Technical Drawings	Withdrawn	DIN ISO 6411	ISO 6411
DIN 338	Parallel shank twist drills, jobber series	Active
DIN 352	Sets of taps – Sets of 3 taps for metric coarse ISO-threads M1 to M68	Active
DIN 371	Machine taps with reinforced shank for coarse pitch metric ISO-threads M1 to M10 and fine pitch metric ISO-threads M1 × 0,2 to M10 × 1,25	Active
DIN 374	Machine screwing taps for fine pitch metric ISO-threads M3 × 0,2 to M52 × 4	Active

DIN 400 to DIN 499

DIN	Title	Status	DIN replacement	Other org replacement
DIN 404	Slotted capstan screws	Active
DIN 406-10	Engineering drawing practice; dimensioning; concepts and general principles	Active
DIN 406-11	Engineering drawing practice; dimensioning; principles of application	Active
DIN 406-12	Engineering drawing practice; dimensioning; tolerancing of linear and angular dimensions (modified version of ISO 406:1987)	Active
DIN 417	Slotted set screws with long dog point	Withdrawn	DIN EN 27435	ISO 7435
DIN 427	Slotted headless screws with chamfered end	Withdrawn	DIN EN ISO 2342	ISO 2342
DIN 428	Hexagon nuts, Grade C	Withdrawn	DIN EN ISO 4034	ISO 4034
DIN 433	Washers for use with cheese head screws	Withdrawn	DIN EN ISO 7092	ISO 7092
DIN 433-1	Product grade A washers – with a hardness up to 250 HV designed for use with cheese head screws	Withdrawn	DIN EN ISO 7092	ISO 7092
DIN 433-2	Product grade A washers – with a hardness up to 300 HV designed for use with cheese head screws	Withdrawn	DIN EN ISO 7092	ISO 7092
DIN 438	Slotted set screws with cup point	Withdrawn	DIN EN 27436	ISO 7436
DIN 439	Hexagon thin nuts	Withdrawn	DIN EN ISO 4035, DIN EN ISO 4036, DIN EN ISO 8675	ISO 4035, ISO 4036, ISO 8675
DIN 439-1	Unchamfered hexagon thin nuts – Product grade B	Withdrawn	DIN EN ISO 4036	ISO 4036
DIN 439-2	Chamfered hexagon thin nuts – Product grades A and B	Withdrawn	DIN EN ISO 4035, DIN EN ISO 8675	ISO 4035, ISO 8675
DIN 440	Washers for use in timber constructions	Withdrawn	DIN EN ISO 7094	ISO 7094
DIN 444	Eyebolts	Active
DIN 461	Graphical Representation in Systems of Coordinates	Active
DIN 462	Machine Tools; Internal Tab Washers for Slotted Round Nuts for Hook Spanner according to DIN 1804	Active
DIN 464	Knurled thumb screws, high type	Active
DIN 466	Knurled nuts, high type	Active
DIN 467	Knurled nuts, low type	Active
DIN 471	Circlips (retaining rings) for shafts; Normal type and heavy type	Active
DIN 472	Circlips (retaining rings) for internal grooves; Normal type and heavy type	Active
DIN 476	Paper sizes	Withdrawn	DIN EN ISO 216	ISO 216
DIN 476-2	Trimmed Sizes of Paper – C Series	Active
DIN 477-1	Gas cylinder valves for cylinder test pressures up to 300 bar – Part 1: Valve inlet and outlet connections	Active
DIN 479	Square head bolts with short dog point	Active

DIN 500 to DIN 599

DIN	Title	Status	DIN replacement	Other org replacement
DIN 522	Metal washers; technical delivery conditions	Withdrawn	DIN EN ISO 4759-3	ISO 4759-3
DIN 548	Round nuts with set pin holes in side	Active
DIN 551	Slotted set screws with flat point	Withdrawn	DIN EN 24766	ISO 4766
DIN 553	Slotted set screws with cone point	Withdrawn	DIN EN 27434	ISO 7434
DIN 555	M5 to M100x6 hexagon nuts – Product grade C	Withdrawn	DIN EN ISO 4034	ISO 4034
DIN 558	Hexagon head screws	Withdrawn	DIN EN ISO 4018	ISO 4018
DIN 580	Collar eyebolts for lifting purposes	Active

DIN 600 to DIN 699

DIN	Title	Status	DIN replacement	Other org replacement
DIN 601	M5 to M52 hexagon head bolts; product grade C	Withdrawn	DIN EN ISO 4016	ISO 4016
DIN 603	Mushroom head square neck bolts	Active
DIN 609	Hexagon fits bolts with long thread	Active
DIN 625-1	Rolling bearings; single row radial contact ball bearings	Active
DIN 625-3	Rolling bearings; double row radial contact ball bearings	Active
DIN 625-4	Rolling bearings; radial contact groove ball bearings with flanged outer ring	Active
DIN 653	Knurled thumb screws, low type	Active
DIN 678-1	Envelopes – Part 1: Sizes	Active
DIN 678-2	Envelopes – Part 2: Envelopes for Processing in Enveloping Machines, Size C6 to C4	Active

DIN 700 to DIN 799

DIN	Title	Status
DIN 763	Tested, non-calibrated, long-link round steel chains	Active
DIN 764-1	Calibrated and tested round steel link chains for continuous conveyors; grade 2, pitch 3,5d	Active
DIN 764-2	Calibrated and tested round steel link chains for continuous conveyors; grade 3, pitch 3,5d	Active
DIN 766	Calibrated and tested grade 3 round steel link chains	Active
DIN 799-1	Foundation Blocks	Active

DIN 800 to DIN 899

DIN	Title	Status	DIN replacement	Other org replacement
DIN 820-1	Standards Work – Part 1: Principles	Active
DIN 820-2	Standardization – Part 2: Presentation of standards; examples for presentation of figures, tables and part lists	Active
DIN 820-3	Standardization – Pdfart 3: Concepts	Active
DIN 820-4	Standardization – Part 4: Working procedure	Active
DIN 820-11	Standardization – Part 11: Presentation of Standards concerning safety regulations which are VDE-Specifications or VDE-Guidelines	Active
DIN 820-12	Standardization – Part 12: Presentation of standards concerning safety regulations	Active
DIN 820-13	Standardization – Part 13: Adoption of European documents of CEN, CENELEC and of ETSI; Concepts and presentation	Active
DIN 820-15	Standardization – Part 15: Implementation of ISO and IEC international documents; Concepts and presentation	Active
DIN 820-120	Standardization – Part 120: Guidelines for the inclusion of safety aspects in standards (ISO/IEC Guide 51:1999)	Active
DIN 824	Technical drawings; Folding to filing size	Active
DIN 899	Hand Operated Wrenches and Sockets; Technical Specifications	Withdrawn	DIN ISO 1711-1	ISO 1711-1

DIN 900 to DIN 999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 906	internal drive pipe plugs for the sealing of holes with cylindrical internal threads	Active
DIN 908	Hexagon socket screw plugs with parallel screw thread	Active
DIN 910	Hexagon-duty hexagon head screw plugs	Active
DIN 911	Hexagon Socket Screw Keys	Withdrawn	DIN ISO 2936	ISO 2936
DIN 912	Hexagon socket head cap screws (modified version of ISO 4762)	Withdrawn	DIN EN ISO 4762, DIN EN ISO 21269	ISO 4762, ISO 21269
DIN 913	Hexagon socket set screws with flat point (ISO 4026 modified)	Withdrawn	DIN EN ISO 4026	ISO 4026
DIN 914	Hexagon socket set screws with cone point (ISO 4027 modified)	Withdrawn	DIN EN ISO 4027	ISO 4027
DIN 915	Hexagon socket set screws with dog point (ISO 4028 modified)	Withdrawn	DIN EN ISO 4028	ISO 4028
DIN 916	Hexagon socket set screws with cup point (ISO 4029 modified)	Withdrawn	DIN EN ISO 4029	ISO 4029
DIN 918	Fasteners; Terminology; Spelling of terms; Abbreviations	Active
DIN 918-3	Overview of European Standards for fasteners	Active
DIN 919-1	Technical Drawings; Wood Processing; Principles	Active
DIN 921	Slotted pan head screws with large head	Active
DIN 923	Slotted pan head screws with shoulder	Active
DIN 929	Hexagon weld nuts	Active
DIN 930	Fine thread pitch partially threaded screws	Withdrawn	DIN 931-1, DIN 931-2
DIN 931-1	M1,6 to M39 Hexagon Cap Screws Partially Threaded – Product grades A and B	Withdrawn	DIN EN ISO 4014	ISO 4014
DIN 931-2	M42 to M160x6 Hexagon Cap Screws Partially Threaded – Product grade B	Withdrawn	DIN EN ISO 4014	ISO 4014
DIN 933	M1,6 to M52 Hexagon Cap Screws Fully Threaded – Product grades 8.8	Withdrawn	DIN EN ISO 4017	ISO 4017
DIN 934	Hexagon nuts with metric coarse and fine pitch thread – Product classes A and B	Withdrawn	DIN EN ISO 4032, DIN EN ISO 8673	ISO 4032, ISO 8673
DIN 935-1	Hexagon slotted nuts and castle nuts with metric coarse and fine pitch thread – Product grades A and B	Active
DIN 935-2	M42 to M160x6 hexagon head nuts; product grade B	Active
DIN 935-3	Hexagon slotted nuts with metric coarse pitch thread – Product grade C	Active
DIN 936	M8 to M52 and M8x1 to M52x3 hexagon thin nuts; product grades A and B	Withdrawn
DIN 937	Hexagon thin castle nuts	Withdrawn
DIN 938	Studs with a length of engagement equal to about 1 d	Active
DIN 939	Studs with a length of engagement equal to about 1,25 d	Active
DIN 946	Determination of coefficient of friction of bolt/nut assemblies under specified conditions	Withdrawn	DIN EN ISO 16047	ISO 16047
DIN 960	M8x1 to M100x4 hexagon head bolts with fine pitch thread – Product grades A and B	Withdrawn	DIN EN ISO 8765, DIN EN ISO 8676	ISO 8765, ISO 8676
DIN 961	M8x1 to M52x3 hexagon head bolts with fine pitch thread – Product grades A and B	Withdrawn	DIN EN ISO 8676	ISO 8676
DIN 962	Designation system for fasteners	Active
DIN 963	Slotted countersunk head screws (with countersunk heads as specified in ISO 2009-1972)	Withdrawn	DIN EN ISO 2009	ISO 2009
DIN 964	Slotted raised countersunk oval head screws	Withdrawn	DIN EN ISO 2010	ISO 2010
DIN 965	Cross recessed countersunk flat head screws	Withdrawn	DIN EN ISO 7046-1, DIN EN ISO 7046-2	ISO 7046-1, ISO 7046-2
DIN 966	Cross recessed raised countersunk head screws	Withdrawn	DIN EN ISO 7047	ISO 7047
DIN 970	Hexagon nuts; Style 1; Metric coarse thread, Product grades A and B; ISO 4032 modified	Withdrawn	DIN EN ISO 4032	ISO 4032
DIN 971-1	Style 1 hexagon nuts with metric fine pitch thread; property classes 6 and 8	Withdrawn	DIN EN ISO 8673	ISO 8673
DIN 971-2	Style 2 hexagon nuts with metric fine pitch thread; property classes 10 and 12	Withdrawn	DIN EN ISO 8674	ISO 8674
DIN 972	M5 to M39 hexagon nuts; style 1; product grade C (modified version of ISO 4034)	Withdrawn	DIN EN ISO 4034	ISO 4034
DIN 975	Threaded rods	Withdrawn	DIN 976-1, DIN 976-2
DIN 976-1	Metric thread stud bolts	Active
DIN 976-2	Metric interference-fit thread stud bolts	Active
DIN 977	Hexagon weld nuts with flange	Withdrawn	DIN EN ISO 21670	ISO 21670
DIN 979	Hexagon thin slotted nuts and castle nuts with metric coarse and fine pitch thread – Product grades A and B	Active
DIN 980	All-metal prevailing torque type hexagon nuts	Withdrawn	DIN EN ISO 7042, DIN EN ISO 10513	ISO 7042, ISO 10513
DIN 981	Locknuts for use with rolling bearings	Active
DIN 982	Prevailing torque type hexagon nuts with nonmetallic insert	Withdrawn	DIN EN ISO 7040, DIN EN ISO 10512	ISO 7040, ISO 10512
DIN 983	Retaining rings with lugs for use on shafts (external circlips)	Active
DIN 985	Prevailing torque type hexagon thin nuts with nonmetallic insert	Withdrawn	DIN EN ISO 10511	ISO 10511
DIN 986	Prevailing torque type hexagon domed cap nuts with non-metallic insert	Active
DIN 988	Shim rings and supporting rings	Active

DIN 1000 to DIN 9999

DIN 1000 to DIN 1999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 1025-1	Hot rolled I-sections – Part 1: Narrow flange I-sections, I-serie – Dimensions, masses, sectional properties	Active
DIN 1025-2	Hot rolled I-beams – Part 2: Wide flange I-beams, IPB-serie; dimensions, masses, sectional properties	Active
DIN 1025-3	Hot rolled I-beams; wide flange I-beams, light pattern, IPBl-serie; dimensions, masses, sectional properties	Active
DIN 1025-4	Hot rolled I-beams; wide flange I-beams heavy pattern, IPBv-serie; dimensions, masses, sectional properties	Active
DIN 1025-5	Hot rolled I-beams; medium flange I-beams, IPE-serie; dimensions, masses, sectional properties	Active
DIN 1301-1	Units – Part 1: Names and Symbols	Active
DIN 1301-2	Units – Part 2: Submultiples and Multiples for General Use	Active
DIN 1301-3	Units – Part 3: Conversions of Units No Longer To Be Used	Active
DIN 1302	General Mathematical Symbols and Concepts	Active
DIN 1303	Vectors, matrices, tensors; symbols and concepts	Active
DIN 1304-1	Letter symbols for physical quantities – Part 1: Symbols for general use	Active
DIN 1304-2	Letter symbols for physical quantities – Part 2: Symbols for use in meteorology and geophysics	Active
DIN 1304-3	Letter symbols for physical quantities – Part 3: Symbols for use in electric power engineering	Active
DIN 1304-5	Letter symbols for physical quantities – Part 5: Symbols for use in fluid mechanics	Active
DIN 1304-8	Letter symbols for physical quantities – Part 9: Symbols for use in the field of static converters using semiconductor devices	Active
DIN 1304-9	Letter symbols for physical quantities – Part 9: Symbols for equivalent circuits of piezoelectric crystals	Active
DIN 1311-1	(Mechanical) vibrations, oscillations and vibration systems – Part 1: Basic concepts, survey	Active
DIN 1311-2	(Mechanical) vibrations, oscillations and vibration systems – Part 2: Linear vibration systems with single degree of freedom	Active
DIN 1311-3	(Mechanical) vibrations, oscillations and vibration systems – Part 3: Linear time-invariant vibration systems with a finite number of degrees of freedom	Active
DIN 1311-4	Vibration; Vibrating Continua, Waves	Active
DIN 1313	Physical Quantities and Equation; Concepts, Methods of Writing	Active
DIN 1315	Angle; Concepts, Units	Active
DIN 1318	Loudness Level	Active
DIN 1319-1	Fundamentals of Metrology – Part 1: Basic Terminology	Active
DIN 1319-2	Basic Concepts in Metrology – Part 2: Terminology Related To Measuring Equipment	Active
DIN 1319-3	Basic Concepts in Metrology – Part 3: Terminology Relating To the Uncertainty of Measurement and the Assessment of Measuring Instruments and Measuring Equipment	Active
DIN 1319-4	Basic Concepts in Metrology – Part 4: Treatment of Uncertainties in the Evaluation of Measurements	Active
DIN 1320	Acoustics; Terminology	Active
DIN 1324-1	Electromagnetic Field – Part 1. State Quantities	Active
DIN 1324-2	Electromagnetic Field – Part 2. Material Quantities	Active
DIN 1324-3	Electromagnetic Field – Part 3. Electromagnetic Waves	Active
DIN 1325-1	Vocabulary for value management, value analysis and functional analysis – Part 1: Value analysis and functional analysis	Active
DIN 1325-2	Value Management, Value Analysis, Functional Analysis Vocabulary – Part 2: Value Management	Active
DIN 1332	Acoustics; Symbols	Withdrawn	DIN EN ISO 80000-8	ISO 80000-8
DIN 1333	Presentation of Numerical Data	Active
DIN 1338	Writing and Typesetting of Formulae	Active
DIN 1355-1	Time; Calendar, Numbering of Weeks, Date of Day, (Clock) Time	Withdrawn
DIN 1421	Arrangement and Numbering in Texts; Clauses, Paragraphs, Enumerations	Active
DIN 1422-1	Publications in Sciences, Technology, Economy and Administration; Presentation of Manuscripts and Typoscripts	Active
DIN 1422-2	Publications in Sciences, Technology, Economy and Administration; Presentation of Clean Copies for Reprographic Use	Active
DIN 1422-3	Publications in Sciences, Technology, Economy and Administration; Typographical Presentation	Active
DIN 1422-4	Publications in Sciences, Technology, Economy and Administration; Presentation of Scientific and Technical Reports	Active
DIN 1440	Medium type washers for pins	Withdrawn	DIN EN 28738	ISO 8738
DIN 1443	Clevis pins without head	Withdrawn	DIN EN 22340	ISO 2340
DIN 1444	Clevis pins with head	Withdrawn	DIN EN 22341	ISO 2341
DIN 1450	Legibility of Typefaces – General	Active
DIN 1451-1	Lettering – Linear-Antiqua without serifes – General	Active
DIN 1451-2	Typefaces – lineal Linear-Antiqua; lettering for transportation	Active
DIN 1451-3	Lettering – Linear-Antiqua without serifes; lettering for printing	Active
DIN 1451-4	Typefaces – lineal Linear-Antiqua; stenciled lettering for engraving and other processes	Active
DIN 1463-1	Guidelines for the Establishment and Development of Thesauri; Monolingual Thesauri	Active
DIN 1463-2	Guidelines for the Establishment and Development of Thesauri; Multilingual Thesauri	Active
DIN 1470	Grooved Pins, Full Length Parallel-grooved with Pilot	Withdrawn	DIN EN 8739	ISO 8739
DIN 1471	Grooved Pins, Full Length Taper-grooved	Withdrawn	DIN EN 8744	ISO 8744
DIN 1472	Grooved Pins, Half Length Taper-grooved	Withdrawn	DIN EN 8745	ISO 8745
DIN 1473	Grooved Pins, Full Length Parallel-grooved with Chamfer	Withdrawn	DIN EN ISO 8740	ISO 8740
DIN 1474	Grooved Pins, Half Length Reverse-grooved	Withdrawn	DIN EN 8741	ISO 8741
DIN 1475	Grooved Pins, Third Length Centre-grooved	Withdrawn	DIN EN 8742	ISO 8742
DIN 1476	Round Head Grooved Pins	Withdrawn	DIN EN 8746	ISO 8746
DIN 1477	Countersunk Head Grooved Pins	Withdrawn	DIN EN 8747	ISO 8747
DIN 1481	Spring-Type Straight Pins (Roll Pins) – Heavy Type	Withdrawn	DIN EN ISO 8752	ISO 8752
DIN 1505-1	Bibliographic references to documents – Part 1: Full References to Printed and Published Documents	Active
DIN 1505-2	Bibliographic references to documents – Part 2: Rules for Citing	Active
DIN 1505-3	Bibliographic references to documents – Part 3: Indexes of cited documents (bibliographies)	Active
DIN 1511	Pattern Equipment for Foundries; Production and Quality	Withdrawn	DIN EN 12890	EN 12890
DIN 1530-1	Tools for moulding – Part 1: Ejector pins with cylindrical head	Active
DIN 1530-2	Tools for moulding – Part 2: Shouldered ejector pins	Active
DIN 1530-3	Tools for moulding – Part 3: Ejector pins with conical head	Active
DIN 1587	Hexagon domed cap nuts	Active
DIN 1707	Soft Solders; Composition, Technical Delivery Condition	Active	DIN EN ISO 9453	ISO 9453
DIN 1712 Part 1	Aluminium and aluminium alloys – Unalloyed aluminium ingots for remelting – Specifications	Withdrawn	DIN EN 576	EN 576
DIN 1712 Part 3	Aluminium; Half-Finished Products	Withdrawn	DIN EN 573-3	EN 573-3
DIN 1783	Strips, Plates and Sheets of Aluminium and Wrought	Withdrawn	DIN EN 485-4	EN 485-4
DIN 1786	Seamless Drawn Copper Tubes for Piping Systems	Withdrawn	DIN EN 1057	EN 1057
DIN 1798	Round Rod of Aluminium (Highest Grade Aluminium)	Withdrawn	DIN EN 754-3	EN 754-3
DIN 1804	Slotted Round Nut for Hook Spanner; ISO Metric Fine Thread	Active
DIN 1810	Hook wrenches	Active
DIN 1816	Round Nut with Set Pin Holes Inside; ISO Metric Fine Thread	Active
DIN 1897	Spiral drill bits, short length	Active
DIN 1912-1	Graphical Representation of Welded, Soldered and Brazed Joints	Withdrawn	DIN EN ISO 17659	ISO 17659
DIN 1912-2	Graphical Representation of Welded, Soldered and Brazed Joints	Withdrawn	DIN EN ISO 6947	ISO 6947
DIN 1912-4	Graphical Representation of Welded, Soldered and Brazed Joints; Concepts and Terms for Soldered and Brazed Joints and Seams	Active
DIN 1912-5	Symbolic Representation on Drawings of Welded, Soldered and Brazed Joints	Withdrawn	DIN EN 22553	ISO 2553
DIN 1960	Construction contract procedures (VOB) – Part A: General provisions relating to the award of construction contracts	Active
DIN 1961	Construction contract procedures (VOB) – Part B: General conditions of contract relating to the execution of construction work	Active

DIN 2000 to DIN 2999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 2112	Alphanumeric office machines – Alphanumeric keyboards, keyboard arrangement for manually operated typewriters	Withdrawn	DIN 2137-1, DIN 2137-2
DIN 2127	Alphanumeric office machines; alphanumeric keyboards, keyboard arrangement for electro-mechanical operated typewriters	Withdrawn	DIN 2137-1, DIN 2137-2
DIN 2137-1	Keyboards for data and text input – Part 1: German keyboard layout	Active
DIN 2137-2	Keyboards for data and text input – Part 2: Additional requirements	Active
DIN 2181	Sets of 2 taps for metric fine ISO-threads M1 × 0,2 to M52 × 4	Active
DIN 2342-1	Vocabulary of terminology; basic concepts	Active
DIN 2391-1	Seamless precision steel tubes – Part 1: Dimensions	Canceled	DIN EN 10305-1	EN 10305-1
DIN 2391-2	Seamless precision steel tubes – Part 2: Technical delivery conditions	Canceled	DIN EN 10305-1	EN 10305-1
DIN 2448	Seamless Steel Pipes and Tubes – Dimensions, Conventional Masses per Unit Length	Canceled	DIN EN 10220	EN 10220
DIN 2527	Blank flanges – Nominal pressure 6 to 100	Withdrawn	DIN EN 1092-1	EN 1092-1
DIN 2860	Capillary Fittings; Bends 180° of Copper	Withdrawn
DIN 2982	Steel threaded pipe fittings	Withdrawn	DIN EN 10241	EN 10241
DIN 2999-1	Pipe threads for tubes and fittings; parallel internal thread and taper external thread; tread dimensions	Withdrawn	DIN EN 10226-1	EN 10226-1
DIN 2999-2	Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Internal Thread and Conical External Thread, Gauging System and Use of Gauges	Withdrawn	DIN EN 10226-3	EN 10226-3
DIN 2999-3	Whitworth Pipe Threads for Tubes and Fittings; Gauge Dimensions	Withdrawn	DIN EN 10226-3	EN 10226-3
DIN 2999-4	Pipe threads for tubes and fittings; sizes for taper screw limit plug gauges for parallel internal thread	Withdrawn	DIN EN 10226-3	EN 10226-3
DIN 2999-5	Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Screw Limit Ring Gauges for Gauging Conical External Threads, Sizes	Withdrawn	DIN EN 10226-3	EN 10226-3
DIN 2999-6	Whitworth Pipe Threads for Tubes and Fittings; Conical Screw Check Plugs, Sizes	Withdrawn	DIN EN 10226-3	EN 10226-3

DIN 3000 to DIN 3999

DIN	Title	Status	DIN replacement
DIN 3000			,
DIN 3017-1	Hose clamps with worm gear drive; shape A		,
DIN 3017-2	Hose clamps – Part 2: Clamps with fastening lugs		,
DIN 3017-3	Hose clamps – Part 3: Bolt clamps		,
DIN 3017-4	Hose clamps – Part 4: Technical delivery conditions		,
DIN 3017-5	Hose clamps – Part 5: Wide strip hose clamps with fastening lugs; Types D and E		,
DIN 3113	Combination Wrench		,
DIN 3770	Sealing rings ("O-rings") with special accuracy, made of elastomeric materials	Withdrawn
DIN 3771-3	Fluid systems; O-rings; materials, field of application	Active

DIN 4000 to DIN 4999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 4048-1	Water engineering, terms – Part 1: Dam plants	Active
DIN 4048-2	Water engineering, terms – Part 2: Waterpower plants	Active
DIN 4054	Correction of waterways, terms	Active
DIN 4094-1	Subsoil, Field investigations – Part 1: Cone penetration tests	Active
DIN 4102-1	Fire behaviour of building materials and elements – Part 1: Classification of building materials – Requirements and testing	Active
DIN 4102-2	Fire Behaviour of Building Materials and Building Components – Part 2: Building Components; Definitions, Requirements and Tests	Active
DIN 4102-3	Fire Behaviour of Building Materials and Building Components – Part 3: Fire Walls and Non-load-bearing External Walls; Definitions, Requirements and Tests	Active
DIN 4102-4	Fire behaviour of building materials and elements – Part 4: Overview and design of classified building materials, elements and components	Active
DIN 4102-5	Fire Behaviour of Building Materials and Building Components – Part 5: Fire Barriers, Barriers in Lift Wells and Glazings Resistant against Fire; Definitions, Requirements and Tests	Active
DIN 4102-6	Fire Behaviour of Building Materials and Building Components – Part 6: Ventilation Ducts; Definitions, Requirements and Tests	Active
DIN 4102-7	Fire behaviour of building materials and elements – Part 7: Roofing – Concepts, requirements and testing	Active
DIN 4102-8	Fire behaviour of building materials and components – Part 8: Small-scale test furnace	Active
DIN 4102-9	Fire behaviour of building materials and elements – Part 9: seals for cable penetrations; concepts, requirements and testing	Active
DIN 4102-11	Fire behaviour of building materials and building components – Part 10: pipe encasements, pipe bushings, service shafts and ducts, and barriers across inspection openings; terminology, requirements and testing	Active
DIN 4102-12	Fire behaviour of building materials and elements – Part 12: Fire resistance of electric cable systems required to maintain circuit integrity – Requirements and testing	Active
DIN 4102-13	Fire behaviour of building materials and elements – Part 13: Fire resistant glazing; concepts, requirements and testing	Active
DIN 4102-14	Fire behaviour of building materials and elements – Part 14: Determination of the burning behaviour of floor covering systems using a radiant heat source	Active
DIN 4102-15	Fire behaviour of building materials and elements – Part 15: "Brandschacht"	Active
DIN 4102-16	Fire behaviour of building materials and elements – Part 16: "Brandschacht" tests	Active
DIN 4102-17	Fire behaviour of building materials and elements – Part 17: determination of melting point of mineral fibre insulating materials; concepts, requirements and testing	Active
DIN 4102-18	Fire behaviour of building materials and components – Part 18: fire barriers, verification of automatic closure (continuous performance test)	Active
DIN 4102-22	Fire behaviour of building materials and building components – Part 22: Application standard for DIN 4102-4 based on the design of partial safety factors	Active
DIN 4108-1	Thermal protection and energy economy in buildings – Part 1: Quantities and units	Active
DIN 4108-2	Thermal protection and energy economy in buildings – Part 2: Minimum requirements to thermal insulation	Active
DIN 4108-3	Thermal protection and energy economy in buildings – Part 3: Protection against moisture subject to climate conditions; Requirements and directions for design and construction	Active
DIN 4108-7	Thermal insulation and energy economy of buildings – Part 7: Airtightness of building, requirements, recommendations and examples for planning and performance	Active
DIN 4108-10	Thermal insulation and energy economy in buildings – Part 10: Application-related requirements for thermal insulation materials – Factory made products	Active
DIN 4150-1	Structural vibration – Part 1: Prediction of vibration parameters	Active
DIN 4150-2	Structural vibration – Part 2: Human exposure to vibration in buildings	Active
DIN 4150-3	Structural vibration – Part 3: Effects of vibration on structures	Active
DIN 4420-1	Service and working scaffolds – Part 1: Service scaffolds – Performance requirements, general design, structural design	Active
DIN 4512	Photographic sensitometry, determination of optical density: "Photographische Sensitometrie, Bestimmung der optischen Dichte" (1934-01, 1957–11, 1961–10)	Withdrawn	DIN 4512-1:1971-04, DIN 4512-3:1973-01, DIN 4512-4:1977-06, DIN 4512-5:1977-10, DIN 4512-6:1980-07
DIN 4512-1	Photographic sensitometry, determination of the speed of black and white negative materials for pictorial photography (1971-04, 1993–05)	Withdrawn (2000–09)	DIN ISO 6:1996-02	ISO 6
DIN 4512-3	Photographic sensitometry, determination of diffuse transmission density (1973-01)	Withdrawn	DIN 4512-7:1993-01, DIN 4512-8:1993-01, DIN 4512-9:1993-01
DIN 4512-4	Photographic sensitometry; determination of the speed of colour reversal films (1977-06, 1985–08)	Withdrawn (2002–06)	DIN ISO 2240:1998-06	ISO 2240
DIN 4512-5	Photographic sensitometry; determination of the speed of colour negative films (1977-10, 1990–11)	Withdrawn (2002–06)	DIN ISO 5800:1998-06	ISO 5800
DIN 4512-6	Photographic sensitometry; sensitometric illuminants and light sources (1980-07)	Withdrawn
DIN 4512-7	Photographic sensitometry, determination of optical density; concepts, symbols and notations (1993-01)	Active
DIN 4512-8	Photographic sensitometry, determination of optical density; geometric conditions for transmission density (1993-01)	Active
DIN 4512-9	Photographic sensitometry, determination of optical density; spectral conditions (1993-01)	Active
DIN 4512-10	Photographic sensitometry, determination of optical density; geometric conditions for reflection density (1993-01)	Active
DIN V 4701-10	Energy efficiency of heating and ventilation systems in buildings – Part 10: Heating, domestic hot water supply, ventilation	Active
DIN V 4701-12	Energetic evaluation of heating and ventilation systems in existing buildings – Part 12: Heat generation and domestic hot water generation	Active
DIN 4710	Statistics on German meteorological data for calculating the energy requirements for heating and air conditioning equipment	Active

DIN 5000 to DIN 5999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 5008	Rules for text presentation	Active
DIN 5031-1	Physics of radiation in the field of optics and illuminating engineering – Part 1: Quantities, symbols and units of radiation physics	Active
DIN 5031-2	Physics of radiation in the field of optics and illuminating engineering – Part 2: Evaluation of radiation by different detectors	Active
DIN 5031-3	Physics of radiation in the field of optics and illuminating engineering – Part 3: Quantities, symbols and units of illuminating engineering	Active
DIN 5031-4	Physics of radiation in the field of optics and illuminating engineering – Part 4: Efficiencies	Active
DIN 5031-5	Physics of radiation in the field of optics and illuminating engineering – Part 5: Definitions for temperatures	Active
DIN 5031-6	Physics of radiation in the field of optics and illuminating engineering – Part 6: Pupil intensity as a measure of retinal illumination	Active
DIN 5031-7	Physics of radiation in the field of optics and illuminating engineering – Part 7: Terms for wavebands	Active
DIN 5031-8	Physics of radiation in the field of optics and illuminating engineering – Part 8: Definitions and constants of radiation physics	Active
DIN 5031-9	Physics of radiation in the field of optics and illuminating engineering – Part 9: Definitions in the field of luminescence	Active
DIN 5031-10	Physics of radiation in the field of optics and illuminating engineering – Part 10: Photobiologically effective radiation, quantities, symbols and actions	Active
DIN 5035-3	Artificial lighting – Part 3: Lighting of health care premises	Active
DIN 5035-6	Artificial lighting – Part 6: Measurement and evaluation	Active
DIN 5035-7	Artificial lighting – Part 7: Lighting of interiors with visual displays work stations	Active
DIN 5035-8	Artificial lighting – Part 8: Workplace luminaries – Requirements, recommendations and proofing	Active
DIN 5117	Clamp strength for woodworking	Active
DIN 5145	Plane irons for wood smooth and for planes	Active
DIN 5146	Curved irons for jack planes	Active
DIN 5406	Lockwashers and locking plates for use with rolling bearings	Active
DIN 5466-1	Splined joints, calculation of load capacity – Part 1: general basis	Active
DIN 5473	Logic and set theory; symbols and concepts	Active
DIN 5474	Signs in mathematical logic	Withdrawn	DIN 5473
DIN 5475-1	Complex quantities; nomenclature	Withdrawn	DIN 5483-3
DIN 5480-1	Involute splines based on reference diameters – Part 1: Generalities	Active
DIN 5480-2	Involute splines based on reference diameters – Part 2: Nominal and inspection dimensions	Active
DIN 5480-15	Involute splines based on reference diameters – Part 15: Inspection	Active
DIN 5483-1	Time-dependent quantities – Part 1: Terms for the time-dependency	Active
DIN 5483-2	Time-dependent quantities – Part 2: Letter symbols	Active
DIN 5483-3	Time-dependent quantities – Part 3: Complex representation of sinusoidal time-dependent quantities	Active
DIN 5486	Notation of matrices	Withdrawn	DIN 1303
DIN 5487	Fourier-, Laplace- and Z-transformation; symbols and concepts	Active
DIN 5489	Directions and signs in electrical engineering; rules for electric and magnetic circuits, equivalent circuit diagrams	Withdrawn	DIN EN 60375	EN 60375
DIN 5493-2	Logarithmic quantities and units – Part 2: Logarithmic ratios, levels in nepers and decibels	Active
DIN 5510-2	Fire test to railway components	Active
DIN 5590	Compressed air equipment for rail vehicles – Pressure vessels made of steel – Dimensions, designation	Active

DIN 6000 to DIN 6999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 6303	Knurled nuts	Active
DIN 6304	Tommy screws with fixed clamping bolt	Active
DIN 6305	Tommy nuts with fixed clamping bolt	Active
DIN 6306	Tommy screws with movable clamping bolt	Active
DIN 6307	Tommy nuts with movable clamping bolt	Active
DIN 6310	Spring-loaded catch for jigs	Active
DIN 6311	Thrust pads	Active
DIN 6314	Clamp, straight	Active
DIN 6315	Clamp, forked	Active
DIN 6316	Goose neck clamp	Active
DIN 6318	Stepped packing blocks as support for clamps	Active
DIN 6319	Spherical washers and conical seats	Active
DIN 6320	Feet with threaded shank for jigs and fixtures	Active
DIN 6321	Support and location pins	Active
DIN 6323	Slot stones, loose	Active
DIN 6325	Parallel Pins, Hardened; Tolerance Zone m6	Withdrawn	DIN EN ISO 8734	ISO 8734
DIN 6340	Washers for clamping devices	Active
DIN 6738	Paper and paper board – Lifespan classes	Active
DIN 6776	Technical drawings, labeling	Withdrawn	DIN EN ISO 3098	ISO 3098
DIN 6796	Conical spring washers for bolted connections	Active
DIN 6797	Toothed lock washers	Withdrawn
DIN 6798	Serrated lock washers	Withdrawn
DIN 6799	Lock washers (retaining washers) for shafts	Active
DIN 6880	Bright Key Steel; Dimensions, Permissible Variations, Weights	Active
DIN 6885-1	Drive Type Fastenings without Taper Action – Part 1: Parallel Keys, Keyways, Deep Pattern	Active
DIN 6885-2	Drive Type Fastenings without Taper Action – Part 2: Parallel Keys, Keyways, Deep Pattern for Machine Tools, Dimensions and Application	Active
DIN 6885-3	Drive Type Fastenings without Taper Action – Part 3: Parallel Keys, Shallow Pattern, Dimensions and Application	Active
DIN 6900	Screw and Washer Assemblies	Withdrawn	DIN EN 10644	EN 10644
DIN 6901	Tapping screw and washer assemblies	Withdrawn	DIN EN 10510	EN 10510
DIN 6902	Plain washers for screw and washer assemblies	Withdrawn	DIN EN 10673	EN 10673
DIN 6903	Plain washers for tapping screw and washer assemblies	Withdrawn	DIN EN 10669	EN 10669
DIN 6912	Hexagon socket head cap screws with center, with low head	Active
DIN 6914	High-strength hexagon head bolts with large widths across flats for structural steel bolting	Withdrawn	DIN EN 14399-4	EN 14399-4
DIN 6915	Steel hexagon nuts with large widths across flats for high-strength structural bolting	Withdrawn	DIN EN 14399-4	EN 14399-4
DIN 6916	Round washers for high-strength structural steel bolting	Withdrawn	DIN EN 14399-6	EN 14399-6
DIN 6921	Hexagon flange bolts	Withdrawn	DIN EN 1665	EN 1665
DIN 6922	Hexagon flange bolts with reduced shank	Withdrawn	DIN EN 1665	EN 1665
DIN 6923	Hexagon nuts with flange	Withdrawn	DIN EN 1661	EN 1661
DIN 6924	Prevailing torque type hexagon nuts with nonmetallic insert	Withdrawn	DIN EN ISO 7040, DIN EN ISO 10512	ISO 7040, ISO 10512
DIN 6925	Prevailing torque type all-metal hexagon nuts	Withdrawn	DIN EN ISO 7042, DIN EN ISO 10513	ISO 7042, ISO 10513
DIN 6926	Prevailing torque type hexagon nuts with flange and with non-metallic insert	Withdrawn	DIN EN 1663, DIN EN 1666	ISO 7043 (modified), ISO 12125 (modified)
DIN 6927	Prevailing torque type all-metal nuts with flange	Withdrawn	DIN EN 1664, DIN EN 1667	ISO 7044 (modified), ISO 12126 (modified)
DIN 6935	Cold bending of flat rolled steel	Active

DIN 7000 to DIN 7999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 7045	Pan head screws with type H or type Z cross recess – product grade A	Active
DIN 7245	Saw blades for web saws	Active
DIN 7337	Break mandrel blind rivets	Withdrawn	DIN EN ISO 14589, DIN EN ISO 15977, DIN EN ISO 15978, DIN EN ISO 15979, DIN EN ISO 15980, DIN EN ISO 15981, DIN EN ISO 15982, DIN EN ISO 15983, DIN EN ISO 15984, DIN EN ISO 16582, DIN EN ISO 16583, DIN EN ISO 16584	ISO 14589, ISO 15977, ISO 15978, ISO 15979, ISO 15980, ISO 15981, ISO 15982, ISO 15983, ISO 15984, ISO 16582, ISO 16583, ISO 16584
DIN 7343	Spiral Pins; Normal Type	Withdrawn	DIN EN ISO 8750	ISO 8750
DIN 7344	Spiral Pins; Heavy Duty Type	Withdrawn	DIN EN ISO 8748	ISO 8748
DIN 7346	Spring-Type Straight Pins; (Roll Pins) Light-weight Type	Withdrawn	DIN EN ISO 13337	ISO 13337
DIN 7349	Plain Washers for Bolts with Heavy Clamping Sleeves	Active
DIN 7500-1	Thread rolling screws for metric ISO thread – Part 1: Types, designation, requirements	Active
DIN 7500-2	Thread rolling screws for ISO metric thread; guideline values for hole diameters	Active
DIN 7504	Self-drilling screws with tapping screw thread – Dimensions, requirements and testing	Withdrawn	ISO 10666, ISO 15480, ISO 15481, ISO 15482, ISO 15483
DIN 7513	Hexagon head and slotted head thread cutting screws – Dimensions, requirements and testing	Active
DIN 7516	Cross recessed head thread cutting screws – Dimensions, requirements and testing	Active
DIN 7603	Ring seals and gaskets	Active
DIN 7875	Diving accessories for skin divers; terminology	Withdrawn
DIN 7876	Diving accessories for skin divers; flippers; dimensions, requirements and testing	Withdrawn
DIN 7877	Diving accessories for skin divers; diver's masks; requirements and testing	Withdrawn
DIN 7878	Diving accessories for skin divers; snorkel; technical requirements of safety, testing	Withdrawn
DIN 7962	Cross recesses for screws; (modified version of ISO 4757)	Withdrawn	DIN EN ISO 4757	ISO 4757
DIN 7970	Threads and thread ends for tapping screws (modified version of ISO 1478)	Withdrawn	DIN EN ISO 1478	ISO 1478
DIN 7971	Slotted pan head tapping screws	Withdrawn	DIN ISO 1481	ISO 1481
DIN 7972	Slotted countersunk head tapping screws	Withdrawn	DIN ISO 1482	ISO 1482
DIN 7973	Slotted raised countersunk head tapping screws	Withdrawn	DIN ISO 1483	ISO 1483
DIN 7977	Taper Pins with Thread Ends and Constant Point Lengths	Withdrawn	DIN EN 28737	ISO 8737
DIN 7978	Taper Pins with Internal Thread	Withdrawn	DIN EN 28737	ISO 8736
DIN 7979	Parallel Pins with Internal Thread	Withdrawn	DIN EN ISO 8733, DIN EN ISO 8735	ISO 8733, ISO 8735
DIN 7980	Spring lock washers with square ends for cheese head screws	Withdrawn
DIN 7981	Cross recessed pan head tapping screws	Withdrawn	DIN ISO 7049	ISO 7049
DIN 7982	Cross recessed countersunk head tapping screws	Withdrawn	DIN ISO 7050	ISO 7050
DIN 7983	Countersunk (Flat) Head Tapping Screws with Cross Recess	Withdrawn	DIN ISO 7051	ISO 7051
DIN 7984	Hexagon socket head cap screws with low head	Active
DIN 7985	Cross recessed raised Phillips Pan head screws	Withdrawn	DIN EN ISO 7045	ISO 7045
DIN 7989-1	Washers for steel structures – Product grade C	Active
DIN 7989-2	Washers for steel structures – Product grade A	Active
DIN 7991	Hexagon socket countersunk head cap screws	Withdrawn	DIN EN ISO 10642	ISO 10642

DIN 8000 to DIN 8999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 8074	Polyethylene (PE) pipes – Dimensions	Active
DIN 8075	Polyethylene (PE) pipes – PE 63, PE 80, PE 100, PE-HD – General quality requirements, testing	Active
DIN 8077/8078	Polypropylene (PP-R) Pipes -PN 20, PN25 PP-R – General quality requirements, testing	Active
DIN 8513-1	Brazing and Braze Weld Filler Metals; Copper Base Brazing Alloys; Composition, Use, Technical Conditions of Delivery	Withdrawn	DIN EN 1044	EN 1044
DIN 8513-2	Brazing and Braze Weld Filler Metals; Silver-bearing Brazing Alloys with less than 20% by wt. Silver; Composition, Use, Technical Conditions of Delivery	Withdrawn	DIN EN 1044	EN 1044
DIN 8513-3	Brazing filler metals; silver brazing filler metals containing not less than 20% of silver; composition, application, technical delivery conditions	Withdrawn	DIN EN 1044	EN 1044
DIN 8513-4	Brazing and Braze Weld Filler Metals; Aluminium-Base Brazing Alloys; Composition, Use, Technical Conditions of Delivery	Withdrawn	DIN EN 1044	EN 1044
DIN 8513-5	Brazing filler metals; Nickel base filler metals for high temperature brazing; Application, composition, technical delivery conditions	Withdrawn	DIN EN 1044	EN 1044
DIN 8580	Manufacturing processes – Terms and definitions, division	Active
DIN 8806-1	Narrow band saw blades for woodworking; dimensions	Active
DIN 8515	Defects in Metallic Solder Joints; Brazing Joints and High-temperature Solder Joints; Classification, Designations, Explanatory Notes	Withdrawn	DIN EN ISO 18279:2004-04

DIN 9500 to DIN 9999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 9021	Plain washers with large outside diameter	Withdrawn	DIN EN ISO 7093-1, DIN EN ISO 7093-2	ISO 7093-1, ISO 7093-2

DIN 10000 to DIN 19999

DIN 10000 to DIN 10999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 10504	Food hygiene – Lamps for the lighting of meat and meat products	Withdrawn

DIN 11000 to DIN 11999

DIN	Title	Status	Other org replacement
DIN 11024	Beta cotter pin (R-pin) – Dimensions, materials	Active
DIN 11850	Tubes for the food, chemical and pharmaceutical industry – Stainless steel tubes – Dimensions, materials	Withdrawn	EN 10357
DIN 11851	Hygienic Unions

DIN 12000 to DIN 12999

DIN	Title	Status
DIN 12950-1	Laboratory furniture; safety cabinets for microbiological and biotechnological work; safety requirements, tests	Withdrawn
DIN 12950-2	Laboratory furniture; safety cabinets for microbiological and biotechnological work; containment of class 1 and class 2 cabinets, microbiological test	Withdrawn
DIN 12950-10	Laboratory furniture; safety cabinets for microbiological and biotechnological work; requirements and testing	Withdrawn
DIN 12975-1	Thermal solar systems and components – Solar collectors – Part 1: General requirements
DIN 12975-2	Thermal solar systems and components – Solar collectors – Part 2: Test methods
DIN 12976-1	Thermal solar systems and components – Factory made systems – Part 1: General requirements
DIN 12976-2	Thermal solar systems and components – Factory made systems – Part 2: Test methods

DIN 13000 to DIN 13999

DIN	Title	Status	DIN replacement
DIN 13080	Division of hospitals into functional areas and functional sections	Active
DIN 13260-2	Supply systems for medical gases – Part 2: Dimensions and allocation of probes and gas-specific connection points for terminal units for compressed medical gases and vacuum	Active
DIN 13432	Packaging – Requirements for packaging recoverable through composting and biodegradation – Test scheme and evaluation criteria for the final acceptance of packaging	Active	DIN EN 13432
DIN 13715	Workpiece corners and edges	Active	DIN ISO 13715(2000–12)

DIN 14000 to DIN 14999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 14090	Areas for the fire brigade on premises	Active
DIN 14096-1	Fire precaution regulation – Part 1: General and part A (placard); rules for drafting and placarding	Active
DIN 14096-2	Fire precaution regulation – Part 2: Part B (for persons without special tasks of fire prevention and fire fighting); rules for drafting	Active
DIN 14096-3	Fire precaution regulation – Part 3: Part C (for persons with special tasks of fire prevention and fire fighting); rules for drafting	Active
DIN 14210	Water pool for firefighting	Active
DIN 14236	Ultrasonic domestic gas meters	Active
DIN 14406-4	Portable fire extinguishers – Part 4: Maintenance	Active
DIN 14503	Trailers for firefighting purposes, two-wheeled; general requirements	Withdrawn	DIN 14521
DIN 14505	Firefighting and rescue service vehicles – Vehicles for roller containers – General requirements	Active
DIN 14507	Rescue service vehicles – Vehicles for roller containers – General requirements	Active
DIN 14520	Trailers for portable fire pumps	Withdrawn
DIN 14521	Firefighting – Trailer with removable foam-water monitor	Active
DIN 14530-5	Fire fighting vehicles – Part 5: Group pumping appliance LF 10/6, Group pumping appliance for rescue operations HLF 10/6	Active
DIN 14530-11	Fire fighting vehicles – Part 11: Group pumping appliance LF 20/16, Group pumping appliance for rescue operations HLF 20/16	Active
DIN 14530-16	Fire fighting vehicles – Part 16: Pumping appliance TSF	Active
DIN 14530-17	Fire fighting vehicles – Part 17: Pumping appliance TSF-W	Active
DIN 14530-21	Fire fighting vehicles – Part 21: Pump water tanker TLF 20/40, Pump water tanker TLF 20/40-SL	Active
DIN 14530-22	Fire fighting vehicles – Part 22: TLF 16/24-TR	Active
DIN 14530-24	Fire fighting vehicles – Part 24: Small pumping appliance KLF	Active
DIN 14530-25	Fire fighting vehicles – Part 25: Pumping appliance STLF 10/6	Active
DIN 14555-1	Vehicles carrying tools and gears – Part 1: General requirements	Active
DIN 14555-3	Vehicles carrying tools and gears – Part 3: Emergency tender RW	Active
DIN 14555-12	Vehicles carrying tools and gears – Part 12: Damage control tender GW-G	Active
DIN 14555-21	Vehicles carrying tools and gears – Part 21: GW-L1 for logistic tasks	Active
DIN 14555-22	Vehicles carrying tools and gears – Part 22: GW-L2 for logistic tasks	Active
DIN 14565	Fire hose tender; Type SW 2000-TR	Withdrawn
DIN 14701-1	Turntable ladders and similar fire fighting vehicles; Purpose, concepts, safety equipment, requirements	Withdrawn	DIN EN 1777	EN 1777
DIN 14701-2	Turntable ladders and similar fire fighting vehicles; Turn table ladders, engine driven	Withdrawn	DIN EN 14043, DIN EN 14044	EN 14043, EN 14044
DIN 14701-3	Turntable ladders and similar fire fighting vehicles; Rescue baskets	Withdrawn	DIN EN 1777	EN 1777
DIN 14702	Turntable ladder DL 16–4, hand operating	Active
DIN 14703	Trailer Ladder AL 16-4	Active
DIN 14710-1	Hook ladder, manufactured using wood; with hinged hook	Withdrawn	DIN EN 1147	EN 1147
DIN 14710-3	Hook light metal ladder	Withdrawn
DIN 14711-1	Scaling ladder; made from wood	Withdrawn	DIN EN 1147	EN 1147
DIN 14711-2	Scaling ladder; made from light metal	Withdrawn	DIN EN 1147	EN 1147
DIN 14711-3	Scaling ladder; socket rungs and socket parts	Withdrawn	DIN EN 1147	EN 1147
DIN 14713	Folding ladder	Withdrawn	DIN EN 1147	EN 1147
DIN 14715-1	Three piece extension ladder made from wood	Withdrawn	DIN EN 1147	EN 1147
DIN 14715-2	Three piece extension ladder; made of light metal	Withdrawn	DIN EN 1147	EN 1147

DIN 15000 to DIN 15999

DIN	Title	Status
DIN 15018-2	Cranes; steel structures; principles of design and construction	Active
DIN 15185-1	Warehouse systems with guided industrial trucks; requirements on the ground, the warehouse and other requirements	Active
DIN 15185-2	Warehousesystems with powered industrials trucks; code of practice for the protection of persons when operating with trucks in narrow aisles; safety requirements, testing	Active
DIN 15721	Film 70 mm; projection reel	Active

DIN 16000 to DIN 16999

DIN	Title	Status
DIN 16518	Classification of types	Active
DIN 16892	Cross-linked high-density polyethylene (PE-X) pipes – General quality requirements and testing	Active
DIN 16893	Cross-linked high-density polyethylene (PE-X) pipes – Dimensions	Active

DIN 17000 to DIN 17999

DIN	Title	Status	DIN replacement
DIN 17175	Seamless Tubes of heat Resistant Steels	Withdrawn	DIN EN 10216-2
DIN 17200	Steels For Quenching And Tempering – Technical Delivery Conditions	Superseded	DIN 10083-1 DIN 10083-2 DIN 10083-3
DIN 17240	Heat Resisting and Highly Heat Resisting Materials for Bolts and Nuts; Quality Specifications	Withdrawn	DIN EN 10269
DIN 17410	Materials for permanent magnets: Technical conditions	Active
DIN 17457		Withdrawn	DIN EN 10217-7
DIN 17458		Withdrawn	DIN EN 10216-5
DIN 17471	Resistance alloys	Active

DIN 18000 to DIN 18999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 18012	House service connections facilities – Principles for planning	Active
DIN 18013	Recesses for meter boards (electric meters)	Active
DIN 18014	Foundation earth electrode – General planning criteria	Active
DIN 18015-1	Electrical installations in residential buildings – Part 1: Planning principles	Active
DIN 18015-2	Electrical installations in residential buildings – Part 2: Nature and extent of minimum equipment	Active
DIN 18015-3	Electrical installations in residential buildings – Part 3: Wiring and disposition of electrical equipment	Active
DIN 18022	Domestic kitchens, bathrooms and WCs; design principles	Withdrawn
DIN 18024-1	Barrier-free built environment – Part 1: Streets, squares, paths, public transport, recreation areas and playgrounds – Design principles	Active
DIN 18024-2	Construction of accessible buildings – Part 2: Publicly accessible buildings and workplaces, design principles	Active
DIN 18065	Stairs in buildings – Terminology, measuring rules, main dimensions	Active
DIN 18379	Construction contract procedures (VOB) – Part C: General technical specifications in construction contracts (ATV) – Installation of air conditioning systems	Active
DIN 18382	Contract procedures for building works – Part C: General technical specifications for building works; Low-voltage installation and medium-voltage installation with nominal voltages up to including 36 kV	Active
DIN 18384	Construction contract procedures (VOB) – Part C: General technical specifications in construction contracts (ATV); Installation of lightning protection systems	Active
DIN 18800-1	Steel structures – Part 1: Design and construction	Withdrawn	DIN EN 1993 DIN EN 1090
DIN 18800-2	Steel structures – Part 2: Analysis of safety against buckling of linear members and frames	Withdrawn	DIN EN 1993
DIN 18800-3	Steel structures – Part 3: Analysis of safety against buckling of plates	Withdrawn	DIN EN 1993
DIN 18800-4	Steel structures – Part 4: Analysis of safety against buckling of shells	Withdrawn	DIN EN 1993
DIN 18800-5	Steel structures – Part 5: Composite structures of steel and concrete – Design and construction	Withdrawn	DIN EN 1994
DIN 18800-7	Steel structures – Part 7: Execution and constructor's qualification	Active		EN 1090-2

DIN 19500 to DIN 19999

DIN	Title	Status	DIN replacement	Other org replacement
DIN V 19222	Control technology – Terminology	Active
DIN 19225	Measurement and control; terminology and classification of controllers	Active
DIN 19226-1	Control technology – Part 1: General terms and definitions	Active
DIN 19226-2	Control technology – Part 2: Terms and definitions; dynamic systems behaviour	Active
DIN 19226-3	Control technology – Part 3: Terms and definitions of switching systems behaviour	Active
DIN 19226-4	Control technology – Part 4: Terms and definitions of control systems	Active
DIN 19226-5	Control technology – Part 5: Functional terms	Active
DIN 19226-6	Control technology – Part 6: Terms and definitions of functional and constructional units	Active
DIN 19227-1	Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functions	Active
DIN 19227-2	Control technology; graphical symbols and identifying letters for process control engineering; representation of details	Active
DIN 19237	Measurement and control; control engineering vocabulary	Withdrawn	DIN 19226-3, DIN 19226-4, DIN 19226-5, DIN 19226-6
DIN 19227-1	Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functions	Withdrawn	DIN EN 62424
DIN 19227-2	Control technology; graphical symbols and identifying letters for process control engineering; representation of details	Active
DIN 19533	Pipe-lines of high-density PE (high-density polyethylene) and low-density PE (low-density polyethylene) for drinking water supply; pipes, pipe connections and fittings for pipe-lines	Withdrawn	DIN EN 12201-1, DIN EN 12201-2, DIN EN 12201-3, DIN EN 12201-5	EN 12201-1, EN 12201-2, EN 12201-3, EN 12201-5
DIN 19704-1	Hydraulic steel structures – Part 1: Criteria for design and calculation	Active
DIN 19704-2	Hydraulic steel structures – Part 2: Design and manufacturing	Active
DIN 19704-3	Hydraulic steel structures – Part 3: Electrical equipment	Active

DIN 20000 to DIN 29999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 20066	Fluid technology – hose lines, dimensions, specifications
DIN 20163	Explosives work
DIN 21800	Hammer and pick signs (mining symbol)
DIN 21908	Mining crevice work; colours
DIN 22101	Conveyor belt for bulk material, fundamentals, analysis and design
DIN 22107	Arrangements for belt conveyor rollers
DIN 22112	Rollers: dimensions, specifications, testing
DIN 23307	Seat leathers for the mining industry (miner's apron)
DIN 23342	Clothing for the mining industry – men's vest with 1/4 sleeves
DIN 23345	Clothing for the mining industry – men's underpants 1/1 length (Long Johns)

DIN 24000 to DIN 24999

DIN	Title	Status
DIN 24190	Ventilation and air conditioning – folded and welded rectangular sheet metal ducts	Withdrawn
DIN 24271-1	Centralised lubrication systems – Concepts – Part 1: Classification	Active
DIN 24340-2	Hydraulic valves; mounting surfaces and connecting plates for directional control valves	Active
DIN 24537	Welding, Warping valves; Steel Grating Floor Standard control valves	Active

DIN 28000 to DIN 28999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 28610-1	Ductile iron pressure pipes with socket with cement-mortar lining for gas and water pipelines; dimensions and masses	Withdrawn	DIN EN 545, DIN EN 969	EN 545, EN 969
DIN 28610-2	Ductile iron pressure pipes with socket for gas and water pipelines rated for pressures over 4 bar up to and including 16 bar; dimensions and masses	Withdrawn	DIN EN 969	EN 969

DIN 30000 to DIN 39999

DIN	Title	Status
DIN 30722-1	Roller contact tipper vehicles, roller containers – Part 1: Roller contact tipper vehicles up to 26 t, roller containers type 1570 made from steel	Active
DIN 30722-2	Roller contact tipper vehicles, roller containers – Part 2: Roller contact tipper vehicles up to 32 t, roller containers type 1570 made from steel	Active
DIN 30722-3	Roller contact tipper vehicles, roller containers – Part 3: Roller contact tipper vehicles up to 12 t, roller containers type 900 made from steel	Active
DIN 30722-4	Roller containers for the transport on road and rail	Active

DIN 31000 to DIN 31999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 31635	Conversion of the Arabic alphabet	Active
DIN 32676	Tri-Clamp Fittings^[2]	Active

DIN 40000 to DIN 49999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 40015	Frequency and wave bands	Active
DIN 40020	Guidelines for the user interface in multimedia equipment for general purpose use (IEC/TR 61997:2001)	Active
DIN 40050-9	Road vehicles; degrees of protection (IP-code); protection against foreign objects; water and contact; electrical equipment	Active
DIN 40101-1	Graphical symbols for use on equipment	Withdrawn
DIN 40101-2	Graphical symbols for use on equipment; graphical symbols from ISO 7000 for electrical engineering	Active
DIN 40108	Electric power technology – Current systems – Concepts, quantities, letter symbols	Active
DIN 40110-1	Quantities used in alternating current theory – Part 2: Two-line circuits	Active
DIN 40110-2	Quantities used in alternating current theory – Part 2: Multi-line circuits	Active
DIN 40146-1	Telecommunications – Part 1: Basic concepts	Active
DIN 40148-1	Transmission systems and two-ports; concepts and quantities	Active
DIN 40148-2	Transmission systems and two-ports; symmetry characteristics of linear two-ports	Active
DIN 40148-3	Transmission systems and two-ports; measures for attenuation	Active
DIN 40200	Nominal value, limiting value, rated value, rating – concepts	Active
DIN 41215	Electrical communication engineering; electromagnetic relays, definitions	Withdrawn
DIN 41301	Electro Sheets; Magnetic Materials for Transformers	Withdrawn
DIN 41309-1	Small transformers and chokes; strip-wound cut cores; types SM, SE, SU, SG and S3U; dimensions materials	Withdrawn
DIN 41309-2	Small transformers and chokes; strip-wound cut cores; technical conditions of delivery for one phase applications; types SM, SE, SU and SG	Withdrawn
DIN 41309-3	Small transformers and chokes; strip-wound cut cores; technical conditions of delivery for three phase applications; type S3U	Withdrawn
DIN 41426	Nominal values of resistors and capacitors	Withdrawn	DIN IEC 60063	IEC 60063
DIN 41429	Colour code for fixed resistors	Withdrawn	DIN EN 60062	EN 60062
DIN 41524	Circular connectors for radio and associated sound equipment three and five-pole connectors	Withdrawn
DIN 41612-1	Two-part connectors for printed board, grid 2,54 mm; common mounting features; survey of types	Withdrawn	DIN 41612-1 S1
DIN 41612-1 S1	Two piece connectors for printed circuits, grid 2,54 mm (0,1 in); general allusions	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-2	Two-part connectors for printed boards; grid 2,54mm; dimensions of types B, C and D	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-3	Two part connectors for printed boards; grid 2,54mm; dimensions of types F and G	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-4	Two-part connectors for printed boards; grid 2,54mm, dimensions of type H	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-5	Two-part connectors for printed boards; grid 2,54mm; ratings, requirements, tests	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-6	Two-part connection for printed boards; grid 2.54mm; dimensions of types Q, R and S	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-7	Two-part connectors for printed boards; grid 2,54 mm; dimensions of types U and V	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-8	Two-part connectors for printed boards; grid 2.54 mm; dimensions of type M	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-8 S1	Two-part connectors for printed boards; grid 2.54 mm; dimensions of type M; survey of special contracts for use with type M	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-9	Two-part connectors for printed boards; grid 2,54 mm; dimensions of type E	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-10	Two-part connectors for printed boards; grid 2,54mm; gauges	Withdrawn	DIN EN 60603-2	EN 60603-2
DIN 41612-102	Two-part connectors for printed boards; dimensions for type X	Withdrawn	DIN 41612-9
DIN 41612-103	Two-part connectors for printed boards; dimensions of type M	Withdrawn	DIN 41612-8
DIN 41652-1	Rack and panel connectors, trapezoidal, round contacts 1 mm; common mounting features and dimensions; survey of types	Active
DIN 41652-2	Rack and panel connectors; trapezoidal, round contacts 1 mm; ratings, requirements, tests	Active
DIN 41750-1	Rack and panel connectors, trapezoidal, round contacts ø1 mm; common mounting features and dimensions; survey of types	Active
DIN 41750-2	Rack and panel connectors, trapezoidal, round contacts ø1 mm; ratings, requirements, tests	Active
DIN 41750-3	Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type A; solder termination for free wiring	Active
DIN 41750-5	Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type C; crimp termination for free wiring	Active
DIN 41782	Guidelines for the presentation of published data	Withdrawn	DIN IEC 60747-2	IEC 60747-2
DIN 41786	Thyristors, definitions	Withdrawn
DIN 41855	Semiconductor devices and integrated circuits; kinds of devices and general terms	Withdrawn
DIN 41855-2	Semiconductor devices and integrated circuits; optoelectronic semiconductor devices; terms and definitions	Withdrawn
DIN 41868	Cases 10 A 3 and 10 B 3 for semiconductor devices; main dimensions	Withdrawn
DIN 41869-1	Case 23 A 3 for semiconductor devices; main dimensions	Withdrawn
DIN 41869-2	Cases 34 A 2 and 34 A 3 for semiconductor devices; main dimensions	Withdrawn
DIN 41869-3	Case 11 A 3 and 11 B 3 for semiconductor devices; main dimensions	Withdrawn
DIN 41869-4	Case 12 A 3 for semiconductor devices; main dimensions	Withdrawn
DIN 41869-5	Case 13 A 3 for semiconductor devices; main dimensions	Withdrawn
DIN 41869-6	Case 14 A 3 for semiconductor devices; main dimensions	Withdrawn
DIN 41869-7	Case type 15 for semiconductor devices; main dimensions	Withdrawn
DIN 41873	Cases type 5 for semiconductor devices and integrated circuits	Withdrawn
DIN 41876	Cases 18 A, B and C with 2 up to 4 terminals for semiconductor devices; main dimensions	Withdrawn
DIN 42400	Terminal markings for electrical equipment; general rules, alphanumeric system	Withdrawn	DIN EN 60445	EN 60445
DIN 42402	Terminal markings for power transformers and reactors	Active
DIN 42403	Terminal markings for power converters	Withdrawn	DIN IEC 61148	IEC 61148
DIN 42673-1	Totally enclosed fan-cooled three-phase induction motors squirrel-cage, type IM B 3, with rolling bearing; mounting dimensions and relationship frame sizes-output ratings	Withdrawn
DIN 42673-2	Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes – output ratings for type of protection increased safety "e"	Active
DIN 42673-3	Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes – output ratings for type of protection flameproof enclosure "d"	Active
DIN 42673-4	Totally enclosed fan-cooled alternating-current polyphase motors with squirrel-cage, design B3, with ball bearings, maximum envelope dimensions	Active
DIN 42802	Touch-protected connector for electromedicine	Active
DIN 42961	Rating plates for rotating electrical machinery; design	Active
DIN 42973	Rated output values for rotating electrical machinery for continuous duty	Active
DIN 43700	Measurement and control – Measurement and control instruments for panel mounting – Nominal front- and cut-out-dimensions	Withdrawn	DIN IEC 61554	IEC 61554
DIN 43780	Electrical measuring instruments; direct acting indicating electrical measuring instruments and their accessories	Withdrawn	DIN EN 60051-1	EN 60051-1
DIN 43802-2	Line scales and pointers for indicating electrical measuring instruments; general requirements	Active
DIN 43802-3	Line scales and pointers for indicating electrical measuring instruments; designs and dimensions	Active
DIN 43802-4	Line scales and pointers for indicating electrical measuring instruments; scale graduation and numbering	Active
DIN 43807	Measuring and control; electrical measuring instruments; terminal markings for switchboard meters, panel meters and measuring transducers for the measurement of power and power factor	Active
DIN 43856	Electricity meters, tariff time switches and ripple control receivers; connection diagrams, terminal marking, circuit diagrams	Active
DIN 43856-2	Electricity meters – Part 2: Marking of auxiliary terminals for tariff devices according to IEC-Report 61354:1995	Active
DIN 43870-1	Meter mounting boards; dimensions based on a grid system	Active
DIN 43870-2	Meter mounting boards; functional area	Active
DIN 43870-3	Meter panels; wirings	Active
DIN 43880	Modular electronics housings	Active
DIN 44070-1	Meter mounting boards; dimensions based on a grid system	Active
DIN 44070-2	Meter mounting boards; functional area	Active
DIN 44070-3	Meter panels; wirings	Active
DIN 44070-4	Meter panels; cover for wiring	Active
DIN 44080	Thermistors; PTC, technical terms and tests	Withdrawn
DIN 44300	Information processing; vocabulary	Withdrawn
DIN 44300-1	Information processing – Concepts – General terms	Withdrawn
DIN 44300-2	Information processing – Concepts – Representation of data	Withdrawn
DIN 44300-3	Information processing – Concepts – Data structures	Withdrawn
DIN 44300-4	Information processing – Concepts – Programming	Withdrawn
DIN 44300-5	Information processing – Concepts – Components of digital computer systems	Withdrawn
DIN 44300-6	Information processing – Concepts – Storage	Withdrawn
DIN 44300-7	Information processing – Concepts – Times	Withdrawn
DIN 44300-8	Information processing – Concepts – Processing functions	Withdrawn
DIN 44300-9	Information processing – Concepts – Process relations and modes of operation	Withdrawn
DIN 45322	Circular connectors for radio and associated sound equipment; six-pole connectors	Withdrawn	DIN EN 60130-9	EN 60130-9
DIN 45323	Connectors for coupling an external low-voltage power to portable entertainment equipment (describes at least two DC coaxial power plugs)	Active
DIN 45500-1	High fidelity audio equipment and systems; minimum performance requirements; Part 1: general	Withdrawn	DIN EN 61305-1	EN 61305-1
DIN 45500-2	High fidelity audio equipment and systems; requirements for tuner equipments	Withdrawn	DIN EN 61305-2	EN 61305-2
DIN 45500-3	High fidelity audio equipment and systems; requirements for disk record reproducing equipments	Withdrawn
DIN 45500-4	High fidelity audio equipment and systems; minimum performance requirements for magnetic recording and reproducing equipment	Withdrawn
DIN 45500-5	High fidelity audio equipment and systems; minimum performance requirements for microphones	Withdrawn
DIN 45500-6	High fidelity audio equipment and systems; minimum performance requirements for amplifiers	Withdrawn	DIN EN 61305-3	EN 61305-3
DIN 45500-7	High fidelity audio equipment and systems; requirements for loudspeakers	Withdrawn	DIN EN 61305-5	EN 61305-5
DIN 45500-8	High fidelity audio equipment and systems; for sets and systems	Withdrawn
DIN 45500-9	High fidelity audio equipment and systems; minimum requirements for magnetic tapes 4 and 6 for audio recordings	Withdrawn
DIN 45500-10	High fidelity audio equipment and systems; minimum performance requirements for headphones	Withdrawn
DIN 45507	Measuring apparatus for frequency variations in sound recording equipment	Withdrawn	DIN IEC 60386	IEC 60386
DIN 45539	Disk record reproducing equipment; directives for measurements, markings and audio frequency connections, dimensions of interchangeable pickups, requirements of play back amplifiers	Withdrawn	DIN IEC 60098	IEC 60098
DIN 45596	Microphones; phantom powering	Withdrawn
DIN 46400-1	Steel flats with special magnetic properties cold rolled, non – oriented, finally annealed magnetic sheet and strip hysteresis loss at frequencies above 100 Hz	Withdrawn	DIN EN 10106	EN 10106
DIN 46400-3	Grain-oriented magnetic steel and strip technical conditions	Withdrawn	DIN EN 10107	EN 10107
DIN 47100	Cords for telecommunication; code of insulated conductors, colour of sheath	Withdrawn
DIN 47301-1	Terms of HF-lines	Active
DIN 47301-2	Terms of HF-lines	Active
DIN 47301-3	Definition of radio frequency transmission lines – mean characteristic impedance – mean standing wave ratio	Active
DIN 48803	Lightning protection system; Arrangement of components and dimensions for mounting	Withdrawn
DIN 48830	Lightning protection system; Description	Withdrawn

DIN 51097 to DIN 59999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 51097	Testing of floor coverings; determination of the anti-slip properties: wet-loaded barefoot areas; walking method; ramp test	Withdrawn	DIN 51130
DIN 51130	Testing of floor coverings; determination of the anti-slip properties: workrooms and fields of activities with slip danger, walking method – ramp test	Withdrawn	DIN 51097
DIN 51501	Lubricants; Lubricating Oils L-AN; Minimum Requirements	Withdrawn
DIN 52368	Testing of particleboards; determination of formaldehyde emission by gas analysis	Withdrawn	DIN EN 717-2	EN 717-2
DIN 53150	Paints and varnishes – Determination of the drying stage of coatings (modified Bandow-Wolff method)	Active
DIN 53438	Testing of combustible materials; response to ignition by small flame	Active
DIN 53452	Testing of Plastics; Flexural Test	Withdrawn	DIN EN ISO 178	ISO 178
DIN 53575	Flexible Cellular Polymeric Materials – Determination of Tear Strength	Withdrawn	DIN EN ISO 8067	ISO 8067
DIN 54836	Testing of combustible materials; determination of ignition temperature	Active
DIN 54837	Determination of burning behaviour using a gas burner	Active
DIN 55003-3	Machine tools; symbols; numerically controlled machine tools	Withdrawn
DIN 58145	Measuring Method for determination of solarization effect of fused silica optical fibers	Active
DIN 58810	Surgical implants; threads for bone screws and nuts	Withdrawn
DIN 58888	Thread connection for microscope objectives	Withdrawn	DIN ISO 8038-1	ISO 8038-1

DIN ISO 53438

DIN 60000 to DIN 69999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 66000	Information processing; switching algebra, mathematical signs and symbols	Active
DIN 66001	Information processing; graphical symbols and their application	Active
DIN 66002	Information processing; handwriting of the digit 0 and of the upper case letter O	Active
DIN 66003	Information technology – 7-bit code	Active
DIN 66004-1	Information processing – Coding on data media – Part 1: Representation of 7-bit code character sets on punched tape 25	Active
DIN 66004-2	Information processing – Coding on data media – Part 2: Representation of 7-bit coded and 8-bit coded character sets on punched cards	Active
DIN 66004-3	Information processing – Coding on data media – Part 3: Representation of 7-bit coded and 8-bit coded character sets on magnetic tape 12	Active
DIN 66004-4	Information processing – Coding on data media – Part 4: Representation of 7-bit coded and 8-bit coded character sets on magnetic tape cassette 3,8	Active
DIN 66004-5	Information processing – Coding on data media – Part 5: Representation of 7-bit coded and 8-bit coded set on media-flexible disk cartridge	Active
DIN 66005	Information processing; representation of packed numerics and binary data recorded on 9 tracks on magnetic tape 12	Active
DIN 66006	Presentation of ALGOL/ALCOR programs on paper tape and punch cards	Withdrawn
DIN 66007	Font CMC 7 for magnetic ink character recognition; characters and nominal dimensions	Withdrawn	DIN ISO 1004	ISO 1004
DIN 66008-1	Font A for optical character recognition; characters and nominal dimensions	Active
DIN 66008-6	Font A for optical character recognition; characters and nominal dimensions; extension of the character set	Active
DIN 66008-7	Font A for optical character recognition; representation of characters by dots in a 9 × 9 matrix	Active
DIN 66009	Font B for optical character recognition; character	Withdrawn
DIN 66020-1	Functional requirements for the interface between data terminal equipment and data circuit-terminating equipment – Part 1: General application	Active
DIN 66020-2	List of definitions for interchange circuits between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) in public data networks	Active
DIN 66020-4	Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE)	Active
DIN 66020-9	Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48,000 bits per second	Active
DIN 66021-1	Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE)	Active
DIN 66021-2	Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48,000 bits per second	Active
DIN 66025-1	Numerical control of machines, format; general requirements	Active
DIN 66025-2	Industrial automation; numerical control of machines; format, preparatory and miscellaneous functions	Active
DIN 66027	Information processing; programming language FORTRAN	Withdrawn
DIN 66215-1	Programming of numerically controlled machines; CLDATA, general structure and record types	Active
DIN 66215-2	Programming of numerically controlled machines; CLDATA; minor elements of type 2000 records (post-processor commands)	Active
DIN 66253-2	Information processing; programming language PEARL	1998
DIN 66234	Information processing; programming language PL/I	Active
DIN 66255	Information processing; programming language PL/I	Active
DIN 66256	Information processing; programming language Pascal	Withdrawn
DIN 66257	Numerical control of machines; concepts	Withdrawn	DIN ISO 2806	ISO 2806
DIN 66258-1	Interfaces and basic data link control procedures for data communication; C S-interface, V S-interface	Withdrawn
DIN 66258-2	Interface and basic data link control procedures for data communication; balanced interface for start-stop transmission using basic data link control procedures on point-to-point connection	Withdrawn
DIN 66261	Information processing; Nassi-Shneiderman flowchart symbols	Active
DIN 66264-1	Industrial automation systems and integration – Multiprocessor Control System for Industrial Machines (MPST) – Part 1: Parallel bus	Active
DIN 66264-2	Multiprocessor control system for industrial machines (MPST); industrial automatics; rules for information interchange	Active
DIN 66303	Information technology – 8 bit code	Active
DIN V 66304	Industrial automation; Computer Aided Design; format for the exchange of standard parts data	Active
DIN 66325-2	Local and Metropolitan Area Networks; LLC; identical with ISO 8802-2:1989	Withdrawn		ISO 8802-2
DIN 66325-4	Local and Metropolitan Area Networks; token-passing bus access method; identical with ISO/IEC 8802-4:1990	Withdrawn		ISO/IEC 8802-4
DIN 66399	Three-part standard regarding the seven security levels of paper shredders; replaces DIN 32757	Active
DIN 69901	Project controlling; project management; concepts	Active

DIN 70000 to DIN 79999

DIN	Title	Status
DIN 71412	Lubricating nipples; cone type	Active
DIN 72311-1	Lead storage batteries; starter batteries for motorcycles, nominal capacities, main dimensions	Active
DIN 72311-4	Lead storage batteries; starter batteries, terminals, vent plugs and filler openings	Active
DIN 72311-8	Lead storage batteries; starter batteries for motor cycles and passenger cars	Active
DIN 72311-13	Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45 and 54 Ah, for lateral basic fastening 10,5	Active
DIN 72311-16	Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45, 54 and 63 Ah, for lateral basic fastening 19	Active
DIN 72311-17	Lead storage batteries; starter batteries, protective covering for terminal	Active
DIN 72311-18	Lead storage batteries; starter batteries with basic fastening 10,5 for passenger cars and commercial vehicles; nominal capacities, main dimensions	Active
DIN 72311-20	Lead storage batteries; starter batteries for commercial vehicles; nominal capacities and main dimensions	Active
DIN 72311-21	Lead storage batteries; starter batteries with 10,5 basic fastening lugs for commercial vehicles; nominal capacities and main dimensions	Active
DIN 72552-1	Terminal markings for motor vehicles; scope, principles, requirements	Active
DIN 72552-2	Terminal markings for motor vehicles; codes	Active
DIN 72552-3	Terminal markings for motor vehicles; examples for application on circuit diagrams	Active
DIN 72552-4	Terminal markings for motor vehicles; summary	Active
DIN 75490	Radio communication devices in motor vehicles; installation space, general requirements	Active

DIN 80000 to DIN 99999

DIN	Title	Status	DIN replacement	Other org replacement
DIN 91379	Characters and defined character sequences in Unicode for the electronic processing of names and data exchange in Europe	Active

References

^ DK 621.882.245 Deutsche Normen Dec. 1952 Linsensenkschrauben mit Längsschlitz
^ "What is DIN 32676? | Sanitary Fittings". sanitaryfittings.us. 28 June 2017. Retrieved 18 September 2018.

External links

[1] DK 621.882.245 Deutsche Normen Dec. 1952 Linsensenkschrauben mit Längsschlitz

[2] "What is DIN 32676? | Sanitary Fittings". sanitaryfittings.us. 28 June 2017. Retrieved 18 September 2018.

[1]

[2]

v t e Deutsches Institut für Normung
DIN standards	DIN 1025 DIN 1451 DIN 1530 DIN 5008 DIN 5009 DIN 31635 DIN 41612 DIN 43700 DIN 4420 DIN 47100 DIN 62056 DIN 72552 DIN 91379 Engschrift ISO 216
Committees	Municipal Services Standards Committee
Connectors	DIN connector Mini-DIN connector Multimedia extension connector
Rails	DIN rail

DIN 1 to DIN 999

DIN 1 to DIN 99

DIN 100 to DIN 199

DIN 200 to DIN 299

DIN 300 to DIN 399

DIN 400 to DIN 499

DIN 500 to DIN 599

DIN 600 to DIN 699

DIN 700 to DIN 799

DIN 800 to DIN 899

DIN 900 to DIN 999

DIN 1000 to DIN 9999

DIN 1000 to DIN 1999

DIN 2000 to DIN 2999

DIN 3000 to DIN 3999

DIN 4000 to DIN 4999

DIN 5000 to DIN 5999

DIN 6000 to DIN 6999

DIN 7000 to DIN 7999

DIN 8000 to DIN 8999

DIN 9500 to DIN 9999

DIN 10000 to DIN 19999

DIN 10000 to DIN 10999

DIN 11000 to DIN 11999

DIN 12000 to DIN 12999

DIN 13000 to DIN 13999

DIN 14000 to DIN 14999

DIN 15000 to DIN 15999

DIN 16000 to DIN 16999

DIN 17000 to DIN 17999

DIN 18000 to DIN 18999

DIN 19500 to DIN 19999

DIN 20000 to DIN 29999

DIN 24000 to DIN 24999

DIN 28000 to DIN 28999

DIN 30000 to DIN 39999

DIN 31000 to DIN 31999

DIN 40000 to DIN 49999

DIN 51097 to DIN 59999

DIN 60000 to DIN 69999

DIN 70000 to DIN 79999

DIN 80000 to DIN 99999

See also

References

External links